EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GC-03-1401-CD

Description
RES NET,THIN FILM,1.4K OHMS,100WV,.25% +/-TOL,-25,25PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GC-03-1401-CD Overview

RES NET,THIN FILM,1.4K OHMS,100WV,.25% +/-TOL,-25,25PPM TC,0303 CASE

WBA-T0303GC-03-1401-CD Parametric

Parameter NameAttribute value
package instructionSMT, 0303
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Manufacturer's serial numberWBA
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance1400 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBA
size code0303
Temperature Coefficient-25,25 ppm/°C
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
[A-Current Signal Detection Device] Sichuan Province-Second Prize
[font=微软雅黑, "][size=14px]This work mainly completed the measurement of frequency and current. We did write a program for the harmonic algorithm, but there were always errors after adding it to the mai...
sigma Electronics Design Contest
Flathead RVB2601 creative application development] @fxyc87 RVB2601-Qiqiao technology
My history posts: [RVB2601 creative application development] @fxyc87 RVB2601 unboxing + hello_worldAs the saying goes, sharpening the knife does not delay the chopping of wood, so you can work better ...
fxyc87 XuanTie RISC-V Activity Zone
MOS Driver
Could you please tell me how to optimize this circuit so that its output waveform has less distortion?...
tangwei8802429 Analog electronics
Looking for a DC/DC step-down chip
Hello everyone, I now want to need a DC/DC step-down chip. The input requirement is DC20V 3.25A and the output is DC 3.4V 14A. If there is a constant source, it would be the best. Thank you. If you ha...
liushiming82 Power technology
Ask for advice from the experts! Design of soft start circuit based on single chip microcomputer
Recently, I want to design a three-phase soft start circuit based on a single-chip microcomputer. The basic components required are: 1.IGBT tube 2. Single chip microcomputer 3. Relay 4. Motor 5. LCD d...
电工新手求指导 Analog electronics
U disk IAP jump APP abnormal
[i=s]This post was last edited by shipeng on 2019-5-15 18:48[/i] [size=3]I recently used the USB_OTG_FS of STM32F429 to make a BOOTLOADER that can read files in the USB disk through USB (PA11, PA12) o...
shipeng stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号