U18J3W3RI2 datasheet, PDF - EEWORLD Datasheet

U18J3W3RI2: DescriptionROCKER SWITCH,STRAIGHT,SPDT,ON-(ON),WP STRAIGHT TERMINAL,ROCKER; CategoryMechanical and electronic products switch; File Size2MB，22 Pages; ManufacturerC&K Components; Environmental Compliance

Download Datasheet Parametric View All

U18J3W3RI2 Overview

ROCKER SWITCH,STRAIGHT,SPDT,ON-(ON),WP STRAIGHT TERMINAL,ROCKER

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Reach Compliance Code	not_compliant
ECCN code	EAR99
Actuator color	BLACK
Actuator length	0.407 inch
Actuator material	NYLON
Actuator type	ROCKER
body width	6.985 mm
body height	8.7884 mm
Body length or diameter	12.7 mm
center contact material	COPPER ALLOY
Center contact plating	GOLD OVER NICKEL
Contact (AC) maximum rated power R load	0.4VA@20VAC
Contact (AC) maximum rated R load	2A@250VAC
Maximum contact current (AC)	2 A
Maximum contact current (DC)	5 A
Contact (DC) maximum rated R load	5A@28VDC
Contact function	ON-(ON)
Contact resistance	0.01 mΩ
Maximum contact voltage (AC)	250 V
Maximum contact voltage (DC)	28 V
Dielectric withstand voltage	1400VAC V
Electrical life	100000 Cycle(s)
End contact material	COIN SILVER
End contact plating	GOLD OVER NICKEL
Shell material	STAINLESS STEEL
Insulation resistance	1000000000 Ω
JESD-609 code	e3
Manufacturer's serial number	7000
Installation features	THROUGH HOLE-STRAIGHT
Maximum operating temperature	85 °C
Minimum operating temperature	-30 °C
seal	EPOXY
surface mount	NO
switch function	SPDT
Switch type	ROCKER SWITCH
Terminal surface	Matte Tin (Sn) - with Nickel (Ni) barrier
Terminal length	0.425 inch
Terminal material	COPPER ALLOY
Termination type	WIRE WRAP

Differences and similarities between detection circuits, filter circuits, frequency selection circuits, threshold comparison circuits, and bandpass circuits: The differences and similarities between detection circuits, filter circuits, frequency selection circuits, threshold comparison circuits, and bandpass circuitsI have been studying circuits for so lon...; QWE4562009 MCU

When designing PCB, how to consider electromagnetic compatibility EMC/EMI, specifically...: [size=4][b]Question[/b][/size] [size=4]How to consider electromagnetic compatibility (EMC/EMI) when designing PCB? What specific aspects should be considered? What measures should be taken? [/size]...; ohahaha PCB Design

How to measure the PWM generated by msp430f149 with an oscilloscope: I connected the red test lead to pin 46 (the pin that generates PWM) and the black test lead to gnd on the board, but the oscilloscope did not display a waveform and the PWM indicator light was flashi...; q胡= TI Technology Forum

EEWORLD University ---- Signal Processing on MSP430 16-bit MCU: Signal Processing on MSP430 16-bit MCU : https://training.eeworld.com.cn/course/4989...; wanglan123 Talking

What should I do if the segment code LCD screen has too many segments and the pins cannot be placed?: [align=left][color=rgb(0, 0, 0)][font=Verdana, Arial, Helvetica, sans-seri][size=14px] There are three common ways to connect segment code LCD screens: 1. Metal pins 2. Zebra stripes 3. FPC, etc.; of ...; 晶拓 Integrated technical exchanges

Qorvo PAC chip application in cordless vacuum cleaner: This vacuum cleaner uses Qorvo's CST32251 chip, which is a highly integrated motor control SoC that integrates power management, 50MHz Cortex-M0 MCU, gate driver, op amp comparator, etc. into the same...; alan000345 RF/Wirelessly

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components