WBA-T0303GC-07-5101-GF datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> WBA-T0303GC-07-5101-GF

WBA-T0303GC-07-5101-GF: DescriptionRES NET,THIN FILM,5.1K OHMS,100WV,2% +/-TOL,-25,25PPM TC,0303 CASE; CategoryPassive components The resistor; File Size484KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/

Download Datasheet Parametric View All

WBA-T0303GC-07-5101-GF Overview

RES NET,THIN FILM,5.1K OHMS,100WV,2% +/-TOL,-25,25PPM TC,0303 CASE

WBA-T0303GC-07-5101-GF Parametric

Parameter Name	Attribute value
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Manufacturer's serial number	WBA
Network Type	Center Tap
Number of terminals	6
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package length	0.762 mm
Package form	SMT
Package width	0.762 mm
method of packing	Tray
Rated power dissipation(P)	0.25 W
Guideline	MIL-PRF-38534
resistance	5100 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	WBA
size code	0303
Temperature Coefficient	-25,25 ppm/°C
Tolerance	2%
Operating Voltage	100 V

Preview

Download Datasheet

View All

Wire Bondable

Ceramic Resistors

WBA Series

•

High resistor density

•

Lower stray capacitance

•

Proven TaNFilm

on ceramic technology

IRC’s WBA series wire bondable ceramic resistors are ideally suited for

your most demanding hybrid application. IRC’s TaNFilm

tantalum nitride

thin ﬁlm technology has years of proven stability, reliability and moisture performance.

IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefﬁcients to ﬁt

a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on

request to the factory.

For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series

resistors.

Electrical Data

Absolute Tolerance

Ratio Tolerance

Absolute TCR

Tracking TCR

Package Power Rating (@ 70°C)

Rated Operating Voltage

(not to exceed

√

P x R )

Operating Temperature

Noise

Substrate Material

Substrate Thickness

Bond Pad Metallization

Backside

to ±0.1%

to ±0.05%

to ±25ppm/°C

to ±2ppm/°C

250mW

100V

-55°C to +150°C

<-30dB

99.6% Alumina

0.015˝ ±0.002

(0.381mm ±0.05)

Gold: 30KÅ minimum

Ceramic (gold available)

Physical Data

T0303 - Tapped network

(0.762mm ±0.025)

0.004˝ min

Bond Pads

A subsidiary of

TT electronics plc

0.030˝ ±0.001

(0.762mm ±0.025)

½R

General Note

IRC reserves the right to make changes in product speciﬁcation without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

• 4222 South Staples Street • Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com

WBA Series Issue January 2009 Sheet 1 of 3

0.030˝ ±0.001

Recommended Resources

Optocoupler controlled oscillator circuit

Unbalanced current drying motor winding circuit

Accurate second pulse signal generation circuit

Photodiode code disk photoelectric circuit

Circuit using TTL/O to control DC load

PID amplifier circuit

Input protection design and fast acquisition issues of 0-10V input ADC circuit based on TI ADS1115: Figure 1 0~10V analog acquisition circuit based on ADS1115Figure 2 Effective resolution I would like to ask the forum masters, 1. 0~10V input, 1mv resolution required, is there a problem with my desig...; xingchen8910 Analog electronics

[Experience] How to replace GigaDevice GD32 and STM32? Differences and precautions: I saw a useful document in other forums about how to replace GigaDevice GD32 and STM32. It gave a detailed introduction to the matters that should be paid attention to during the replacement process. ...; annysky2012 stm32/stm8

FPGA implementation of ECT image reconstruction algorithm.pdf: FPGA implementation of ECT image reconstruction algorithm.pdf...; zxopenljx EE_FPGA Learning Park

The problem of choosing magnification: [i=s]This post was last edited by fdsf on 2020-2-14 17:49[/i]Let’s take a look at the pictures first.The video in the picture (explained in the datasheet later) is a signal collected by C12666MA, whic...; 反倒是fdsf MCU

Program running abnormally, please answer: void tm0_isr() interrupt 1 //10ms interrupt{Key_Scan();count++;if (0count=800){Lcd_BLA=0;}else ;if(800count1000){Lcd_BLA=1;}else;if(count=1000){count=0;}else; }Theoretical value is Lcd_BLA=0 Execution...; cccztw 51mcu

Zero-knowledge ESP8266 Blynk mobile APP tutorial: monitoring indoor temperature and humidity: This time, we will use the combination of blynk app + server (local) + zero-knowledge ESP8266 development board to observe the temperature and humidity conditions obtained by ESP8266 through the mobil...; roc2 DIY/Open Source Hardware

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components