EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

DROF-C37P-I-111

Description
D Type Connector, 37 Contact(s), Male, 0.109 inch Pitch, Solder Terminal, Receptacle
CategoryThe connector    The connector   
File Size326KB,5 Pages
ManufacturerSingatron Enterprises Co
Download Datasheet Parametric View All

DROF-C37P-I-111 Overview

D Type Connector, 37 Contact(s), Male, 0.109 inch Pitch, Solder Terminal, Receptacle

DROF-C37P-I-111 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresFERRITE FILTER, 0.318 FTPRINT
body width0.494 inch
body length2.729 inch
Body/casing typeRECEPTACLE
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialBRASS
contact modeSTAGGERED
Contact resistance8 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
Filter functionYES
maximum insertion force2.502 N
Insulation resistance5000000000 Ω
Insulator colorWHITE
insulator materialGLASS FILLED POLYBUTYLENE TEREPHTHALATE
Manufacturer's serial numberDROF
Plug contact pitch0.109 inch
Match contact row spacing0.112 inch
Installation option 2JACKSCREW
Installation methodRIGHT ANGLE
Installation typeBOARD
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.8448 mm
Plating thicknessFLASH inch
Rated current (signal)5 A
GuidelineUL
reliabilityCOMMERCIAL
Shell surfaceNICKEL
Shell materialSTEEL
Terminal length0.125 inch
Terminal pitch2.7686 mm
Termination typeSOLDER
Total number of contacts37
Evacuation force-minimum value1.112 N
Discussion on Current Detection Circuit in Switching Power Supply
Abstract: This paper introduces the implementation method of the current detection circuit, and discusses the problems of current transformer saturation and secondary current droop that are often enco...
zbz0529 Test/Measurement
I would like to ask about the problem of PWM control LED based on register configuration.
I just want to ask if I need to use the IO port to turn on the LED light after the PWM registers are configured?Or can I just use PWM to dim and brighten the LED, turn the light on and off?Why can I o...
一百年后的自己 51mcu
Popular Science | IoT Architecture and Technical Protocols
With the continuous development of science and technology, especially the birth of 5G , the expansion of the number and coverage of the Internet of Things has brought unprecedented challenges to the I...
alan000345 RF/Wirelessly
Buzzer drive circuit
Buzzers are commonly used devices in circuit design. They are widely used in industrial control alarms, computer room monitoring, access control, computers and other electronic products as early warni...
可乐zzZ MCU
Electronics competition sharing: [D-Simple Circuit Characteristics Tester] Shanghai Division_D Question_80%_A school in Minhang District_Report and thoughts
Simple circuit characteristic tester (Question D)SummaryThis report introduces the design scheme and key points of a simple circuit characteristic tester. This system uses the Arm Cortex M4 microproce...
Jacktang Electronics Design Contest
Design of Practical Low-Power Switching Voltage-Regulated Power Supply
Abstract: This paper introduces the design process of a practical low-power switching voltage-stabilized power supply. Its output voltage is highly stable, the source effect and load effect are small,...
zbz0529 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号