2637LHA13000L6V datasheet, PDF

Datasheet> All Categories > Mechanical and electronic products> switch> 2637LHA13000L6V

2637LHA13000L6V: DescriptionRocker Switch, (on)-off-(on), Momentary, 8A, 24VDC, Screw Terminal, Rocker Actuator, Panel Mount; CategoryMechanical and electronic products switch; File Size333KB，8 Pages; ManufacturerAPEM

Download Datasheet Parametric View All

2637LHA13000L6V Overview

Rocker Switch, (on)-off-(on), Momentary, 8A, 24VDC, Screw Terminal, Rocker Actuator, Panel Mount

2637LHA13000L6V Parametric

Parameter Name	Attribute value
Reach Compliance Code	compliant
ECCN code	EAR99
Actuator length	0.354 inch
Actuator material	POLYAMIDE
Actuator type	ROCKER
Other features	6V FILAMENT LAMP
body width	24.9936 mm
body height	16.9926 mm
Body length or diameter	32.004 mm
center contact material	SILVER
Maximum contact current (DC)	8 A
Contact (DC) maximum rated R load	8A@24VDC
Contact function	(ON)-OFF-(ON)
Contact resistance	0.01 mΩ
Maximum contact voltage (DC)	24 V
Dielectric withstand voltage	2500VRMS V
Electrical life	10000 Cycle(s)
End contact material	SILVER
Shell material	POLYAMIDE
Insulation resistance	1000000000 Ω
Manufacturer's serial number	2600
Installation features	PANEL MOUNT
Maximum operating temperature	85 °C
Minimum operating temperature	-20 °C
surface mount	NO
Switch action	MOMENTARY
Switch type	ROCKER SWITCH
Terminal length	0.437 inch
Termination type	SCREW

Preview

Download Datasheet

View All

2600 series

Power rocker switches

Distinctive features and specifications

❑

Three rocker shapes : plain, V-shaped or concave

❑

Various rocker colours

❑

Frame with protection guard on 2600LP models

❑

Illuminated or non-illuminated

❑

UL, CSA, VDE and NF (EN 61058-1) approved

ELECTRICAL SPECIFICATIONS

• Max. current/voltage rating with resistive load and approved ratings : see table below.

• Initial contact resistance : 10mΩ max.

• Insulation resistance : 1.000 MΩ min. at 500VDC

• Dielectric strength : 2.500 Vrms 50 Hz min. between terminals

3.000 Vrms 50 Hz min. between terminals and metal panel

• Electrical life : 10.000 cycles at full load

APPROVED RATINGS

FUNCTIONS

CSA (double pole)

CSA 22-2

DIRECT CURRENT

EN 61058-1

UL (double pole)

UL 1054

VDE

EN 61058-1

24 VDC

12 VDC

ON - OFF

ON - ON

1/6 HP 125VAC

16A 125VAC

16A 250VAC

1/3 HP 250VAC

10A 125VAC

10A 250VAC

1/6 HP 125/250VAC

10A 125VAC

10A 250VAC

1/6 HP 250VAC

1/6 HP 125VAC

16A 125VAC

16A 250VAC

1/3 HP 250VAC

10A 125VAC

10A 250VAC

1/6 HP 125/250VAC

10(4)A 250VAC

T 85/55

10A

15A

ON - OFF - ON

ON - ON - ON

OTHERS

L I option

10(4)A 250VAC

L I option

10(4)A 250VAC

L I option

10(4)A 250VAC

L I option

10(4)A 250VAC

10A

MATERIALS

GENERAL SPECIFICATIONS

• Case : melamine/polyester

• Frame : polyamide

• Actuator : polyamide

• Contacts :

: silver

: copper, silver plated

• Panel thickness : 0,8 mm to 4 mm (.031 to .157)

• Operating temperature :

- silver contacts (A) : -20°C to +85°C

- silver plated contacts (C) : -10°C to +55°C

AGENCY APPROVALS

EN 61058-1

Availability

: consult factory for details of approved models.

Marking

: approved models are standard marked.

APEM

www.apem.com

D-45

Recommended Resources

Simple and practical remote control detector circuit diagram

DC power switching circuit controlled by photocell

Circuit diagram of 5 transistor amplifier feeding short pulses into 50 coaxial cable

Medical instrument preamplifier

Energy-saving emergency fluorescent lamp power circuit

Eliminate pulse edge jitter circuit

The IO pin of MSP430 is set as input, but it receives the output signal of the Hall sensor, and the chip-side signal does not switch.: The IO pins P2.0, P2.2 and P2.6 of MSP430 are set as inputs, but they receive the output signal of the Hall sensor. After the program is run, the motor is rotated manually (the Hall element of the mot...; Scaler-y Microcontroller MCU

[Serial] [Starlight Lightning STM32F407 Development Board] Chapter 10 Serial Communication Experiment: Chapter 11 Serial Port Communication Experiment 11.1 Purpose Through this experiment, you will master the use of STM32 serial port and realize sending and receiving data through the serial port. For t...; hejecu stm32/stm8

Where do errors in vector network analyzers come from?: The error sources of vector network analyzers are mainly the following three aspects: drift error, random error, and systematic error.1. Drift error: It is caused by changes in the performance of the ...; 博宇讯铭 Test/Measurement

[Perf-V Evaluation] Environment Construction and Marquee Program Running: [i=s]This post was last edited by superstar_gu on 2021-1-29 16:04[/i]2.2.1 Setting up the Vivado hardware development environmentThe core processing chip of the Perf-V development board uses the Xilin...; superstar_gu EE_FPGA Learning Park

The relationship between serial port communication and interruption: Serial communication is divided into two parts: sending and receiving. Sending generally does not require interruption to complete, while receiving generally requires interruption to receive.The sende...; fish001 DSP and ARM Processors

How to use a wiring harness tester to measure small resistance? Here's a method: How to measure small resistance with a wiring harness tester?...; aigtekatdz Test/Measurement

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components