EEWORLDEEWORLDEEWORLD

Part Number

Search

BRP2-S-22-R-4-G1

Description
Board Connector, 22 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size157KB,2 Pages
ManufacturerEaton
Download Datasheet Parametric View All

BRP2-S-22-R-4-G1 Overview

Board Connector, 22 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

BRP2-S-22-R-4-G1 Parametric

Parameter NameAttribute value
MakerEaton
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.113 inch
subject depth0.26 inch
body length2.199 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulator colorBLACK
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial numberBRP2
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
PCB contact patternRECTANGULAR
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.1 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts22
Design of wireless communication terminal system realized by USB to UART technology and wireless technology
1. Introduction   Currently, most instruments and equipment use RS232 interfaces to communicate with computers. However, with the development of computer technology, the hot-swappable USB standard int...
fish001 RF/Wirelessly
How to write arm-poky mixed Makefile
The cross-compilation tool uses ARM-poky-linux-gnueabi-g++ and arm-poky-linux-gnueabi-gcc for mixed compilation1. Create new main.c Makefile myinclude.h test.cppvim main.c//filename main.c#include std...
明远智睿Lan Linux and Android
Inductor and capacitor selection for flyback circuit
Dear experts, how to choose the inductor and capacitor of the general flyback circuit?...
洗洗睡 Power technology
Single-ended input and double-ended output circuit
I recently wanted to make a single-ended input and dual-ended output circuit. My initial plan was to connect two inverting amplifiers in series, as shown in the figure:Later, I looked up a circuit:I t...
cncqzxj Analog electronics
When calculating the circuit branch current and component voltage, how to determine whether the selected loop group is an independent loop using the loop current method?
When calculating the circuit branch current and component voltage, using the loop current method, how do you determine whether the selected loop group is an independent loop? Is there any specific sel...
深圳小花 MCU
Evaluation summary: Domestic FPGA Gaoyun GW1N series development board
Event details: [Domestic FPGA Gaoyun GW1N series development board]Updated to 2022-01-24Evaluation report summary:@Breaking TraditionEvaluation of domestic FPGA Gaoyun GW1N-4 series development board ...
EEWORLD社区 Special Edition for Assessment Centres

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号