EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

SL1-019-U114/01-77

Description
Board Connector, 19 Contact(s), 1 Row(s), Male, Right Angle Reverse, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size218KB,2 Pages
ManufacturerE-tec Interconnect Ltd.
Environmental Compliance
Download Datasheet Parametric View All

SL1-019-U114/01-77 Overview

Board Connector, 19 Contact(s), 1 Row(s), Male, Right Angle Reverse, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

SL1-019-U114/01-77 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerE-tec Interconnect Ltd.
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.1 inch
subject depth0.1 inch
body length1.9 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact completed and terminatedGold (Au)
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage500VAC V
Insulation resistance1000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee4
Manufacturer's serial numberSL1
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE REVERSE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.102 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts19
MSP430 Flash Emulation Tool
MSP430 Flash Emulation Tool**MSP-FET is compatible with Code Composer Studio v6 and above** MSP-FET is a powerful emulation development tool (often called a debug probe) that helps users quickly start...
fish001 Microcontroller MCU
Smart MM32F0270 timer DMA mode output PWM
For controlling stepper motors, the most important control parameters are the number and frequency of pulses. The combination of the two can achieve the required motor acceleration and deceleration cu...
火辣西米秀 Domestic Chip Exchange
If the input power may be 12V or 24V, how should the TVS diode be selected?
[i=s] This post was last edited by z45217 on 2018-12-18 13:53 [/i]The power supply is originally fixed at 12V input. Now it needs to be changed to 12V or 24V. What should the transient suppression dio...
z45217 Analog electronics
About Lithium Battery Pack Monitoring, SOC and Battery Balancing Technology
[i=s]This post was last edited by qwqwqw2088 on 2018-12-18 08:19[/i] [size=4] The BMS electric vehicle battery management system is an important link between the on-board power battery and the electri...
qwqwqw2088 Analogue and Mixed Signal
I am going to make a USB sound card myself and give a few to the forum.
I'm working on an audio project recently, and I'm going to DIY a USB sound card, using the SSS1629 solution, with the following parameters: USB protocol: USB specification v2.0 full speed; USB audio p...
flyriz DIY/Open Source Hardware
About the font design of single chip microcomputer
When LCD display is needed, the display of Chinese characters has not been so convenient (without a *font library). If you are just taking a model, you have to consider the time and flash resources re...
Jacktang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号