7109T1CWASE datasheet, PDF - EEWORLD Datasheet

7109T1CWASE: DescriptionTOGGLE SWITCH,RIGHT ANGLE,SPDT,ON-(ON),R ANGLE PC TAIL TERMINAL,TOGGLE,5; CategoryMechanical and electronic products switch; File Size1MB，14 Pages; ManufacturerC&K Components; Environmental Compliance

Download Datasheet Parametric View All

7109T1CWASE Overview

TOGGLE SWITCH,RIGHT ANGLE,SPDT,ON-(ON),R ANGLE PC TAIL TERMINAL,TOGGLE,5

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	C&K Components
Reach Compliance Code	not_compliant
ECCN code	EAR99
Actuator angle	25 deg
Actuator color	CHROME
Executor completed	BRIGHT CHROME
Actuator length	0.487 inch
Actuator material	BRASS
Actuator type	TOGGLE
body width	6.858 mm
body height	12.7 mm
Body length or diameter	12.7 mm
Casing diameter	0.465 inch
Nozzle length	0.448 inch
Casing type	15/32-32
center contact material	COPPER ALLOY
Center contact plating	SILVER
Contact (AC) maximum rated R load	2A@250VAC
Maximum contact current (AC)	2 A
Maximum contact current (DC)	5 A
Contact (DC) maximum rated R load	5A@28VDC
Contact function	ON-(ON)
Contact resistance	0.01 mΩ
Maximum contact voltage (AC)	250 V
Maximum contact voltage (DC)	28 V
Dielectric withstand voltage	1400VAC V
Electrical life	100000 Cycle(s)
End contact material	COIN SILVER
End contact plating	SILVER
Shell material	STAINLESS STEEL
Insulation resistance	1000000000 Ω
JESD-609 code	e3
Manufacturer's serial number	7000
Installation features	THROUGH HOLE-RIGHT ANGLE
Maximum operating temperature	85 °C
Minimum operating temperature	-30 °C
PCB hole count	5
seal	EPOXY
surface mount	NO
Switch action	MOMENTARY
switch function	SPDT
Switch type	TOGGLE SWITCH
Terminal surface	Matte Tin (Sn) - with Nickel (Ni) barrier
Terminal length	0.125 inch
Terminal material	COPPER ALLOY
Termination type	SOLDER

Determine direction based on the X-NUCLEO-IKS01A3 magnetic field strength value: The intensity obtained by the X-NUCLEO-IKA01A3 magnetic sensor has three values: x, y, and z. After testing, the change direction mainly affects the data x and y, while the data z has little effect. I...; hujj MEMS sensors

How to determine the power or IPP of a TVS tube: The normal operating voltage VCC of the circuit is 24V, the current is 1A, the maximum operating voltage Vmax is 26V, and the maximum transient voltage that the subsequent circuit can withstand is 50V...; aq1261101415 Analog electronics

Half-bridge driver: Half-bridge drivers (also called high-side/low-side drivers) reduce switching losses, adapt to noisy environments, and improve system efficiency.Fundamentals of MOSFET and IGBT gate driver circuits Re...; Jacktang Analogue and Mixed Signal

[Reprint] PWM series: complementary PWM and center-aligned mode: Original author: KVIN Reprinted from here For motor control, complementary PWM is often used. If FOC is used, center-aligned mode (center-aligned mode) is also used. The following is a discussion of c...; 灞波儿奔 Microcontroller MCU

How to use SI4463 RF module: I am going to let the microcontroller communicate via radio frequency, and I bought two E10-433MD radio frequency modules from Chengdu Yibite. The modules use the SI4463 chip. I have been looking for ...; hujj 51mcu

【McQueen Trial】Comparison of the accuracy of several ultrasonic sensor programs of McQueen: [b]Purpose[/b] Compare the test accuracy of several ultrasonic sensors to provide a reference for everyone's use. [b]Methods[/b] Write different programs into microbit, use McQueen's ultrasonic sensor...; dcexpert MicroPython Open Source section

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components