EEWORLDEEWORLDEEWORLD

Part Number

Search

MAX7370

Description
8 x 8 Key-Switch Controller and LED Driver/GPIOs
File Size1MB,37 Pages
ManufacturerMaxim
Websitehttps://www.maximintegrated.com/en.html
Download Datasheet Compare View All

MAX7370 Overview

8 x 8 Key-Switch Controller and LED Driver/GPIOs

19-5950; Rev 0; 6/11
EVALUATION KIT AVAILABLE
MAX7370
8 x 8 Key-Switch Controller and LED Driver/GPIOs
with I
2
C Interface and High Level of ESD Protection
General Description
The MAX7370 I
2
C-interfaced peripheral provides micro-
processors with management of up to 64 key switches,
with optional GPIO and PWM-controlled LED drivers.
The key-switch drivers interface with metallic or resistive
switches with on-resistances up to 5kI. Key inputs are
monitored statically, not dynamically, to ensure low-EMI
operation. The IC features autosleep and autowake
modes to further minimize the power consumption of
the device. The autosleep feature puts the device in a
low-power state (1µA typ) after a timeout period. The
autowake feature configures the device to return to
normal operating mode from sleep upon a keypress.
The key controller debounces and maintains a FIFO
buffer of keypress and release events (including auto-
repeat, if enabled). An interrupt (INT) output can be
configured to alert keypresses, as they occur, or at the
maximum rate.
The same index rows and columns in the device can be
used as a direct logic-level translator.
If the device is not used for key-switch control, all
keyboard pins can be used as GPIOs. Each GPIO can
be programmed to one of the two externally applied
logic voltage levels. Four column ports (COL7–COL4)
can also be configured as LED drivers that feature
constant-current and PWM intensity control. The maximum
constant-current level for each open-drain LED port is
20mA. The intensity of the LED on each open-drain port
can be individually adjusted through a 256-step PWM
control.
The device is offered in a 24-pin (3.5mm x 3.5mm) TQFN
package with an exposed pad, and small 25-bump
(2.159mm x 2.159mm) wafer-level package (WLP) for
cell phones, pocket PCs, and other portable consumer
electronic applications.
The device operates over the -40°C to +85°C extended
temperature range.
Features
S
Monitors Up to 64 Keys
S
Integrated High-ESD Protection
±8kV IEC 61000-4-2 Contact Discharge
±14kV IEC 61000-4-2 Air-Gap Discharge
S
Keyscan Uses Static Matrix Monitoring for
Low-EMI Operation
S
Four LED Driver Pins on COL7–COL4
S
5V Tolerant, Open-Drain I/O Ports Capable of
Constant-Current LED Drive
S
256-Step PWM Individual LED Intensity-Control
Accuracy
S
Individual LED Blink Rates and Common LED
Fade In/Out Rates from 256ms to 4096ms
S
FIFO Queues Up to 16 Debounced Key Events
S
User-Configurable Keypress and Release
Debounce Time (2ms to 32ms)
S
Key-Switch Interrupt (INT) on Each Debounced
Event/FIFO Level, or End-of-Definable Time Period
S
1.62V to 3.6V Operating Supply Voltage
S
Individually Programmable GPIOs to Two Logic
Levels
S
8-Channel Individual Programmable Level
Translators
S
Provides Optional GPIOs on all ROW½ and COL½
Pins
S
Supports Hot Insertion
S
400kbps, 5.5V Tolerant I
2
C Serial Interface with
Selectable Bus Timeout
Ordering Information
appears at end of data sheet.
Typical Operating Circuit
+1.8V
V
CC
+2.6V
V
LA
COL4
COL5
COL6
COL7
ROW[0:7]
GND
COL[0:3]
8
4
32 KEYS
+5V
Applications
Cell Phones
Notebooks
PDAs
Handheld Games
Portable Consumer Electronics
For related parts and recommended products to use with this part,
refer to
www.maxim-ic.com/MAX7370.related.
MCU
INT
SDA
SCL
AD0
MAX7370
I/O
I/O
½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½½
Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.

MAX7370 Related Products

MAX7370 MAX7370ETG MAX7370EWA
Description 8 x 8 Key-Switch Controller and LED Driver/GPIOs 8 x 8 Key-Switch Controller and LED Driver/GPIOs with I2C Interface and High Level of ESD Protection 8 x 8 Key-Switch Controller and LED Driver/GPIOs with I2C Interface and High Level of ESD Protection
Verilog Typical Circuit Design_Huawei.pdf
Verilog Typical Circuit Design_Huawei.pdf...
zxopenljx EE_FPGA Learning Park
Frequency Characteristics Analysis of Amplifier Circuit
I. Brief description of frequency characteristics  (1) Since there is a reactive element C in the amplifier circuit , it presents different impedances for different frequencies, so the amplifier circu...
Jacktang Analogue and Mixed Signal
Problems encountered in AD18 copper plating
When laying copper, I don’t know where the rule was designed wrong. It was supposed to connect to the GND network, but now all of them are avoided....
XIAOLAN123 PCB Design
Solution to the error "Unable to connect to localhost:3333" when downloading the Xianji development board
Today, when I was using HPM6750EVKMINI, the download prompt "Unable to connect to localhost:3333" appeared. The download of the example program that worked well before also had this prompt.After the d...
littleshrimp Domestic Chip Exchange
Eight working modes of LoRa
After starting the LoRa mode (i.e. setting the LongRangeMode bit of RegOpMode), you can set the LoRa working mode. . As shown in the following table:By changing the value of the RegOpMode register, yo...
Aguilera RF/Wirelessly
Testing methods and diagnostic analysis for DSP-containing circuit boards
[i=s]This post was last edited by Baboerben on 2019-5-20 23:17[/i] [p=30, 2, left][size=4]In modern radar systems, DSP circuit boards are widely used. DSP circuit boards usually use a certain DSP chip...
灞波儿奔 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号