85°C ± 2°C, 85%±5%RH, 1000 hours; 1.5 hr ON, 0.5 hr OFF cycle
85°C ± 2°C, 3000 hours, 1.5 hr ON, 0.5 hr OFF cycle
+155°C, 1000 hours
* Depends on resistance value, please contact KOA Speer for details.
Precautions for Use
• The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts
absorb on the top tapes to cause a failure in the mounting and the parts are destructed by static electricity (1J, 2A, 2B, 2E: 1kV and more, 1E: 0.5kV and more at Human
Body Model 100pF, 1.5kΩ) to change the resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged
on the tapes. Similarly, care should be given not to apply the excessive static electricity when mounting on the boards.
• Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc.
The flux may contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na? ), chlorine (Cl−) etc. Therefore these
kinds of ionic substances may induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since
lead free solder contains ionic substances. Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
●
The upper electrodes could be peeled off when a heat-resistant masking tape is attached to the mounted chip resistors and then detached from them. It is confirmed that
the adhesiveness gets stronger due to the exposure to heat under mounting. Accordingly, we recommend the use of masking tape be refrained. If the use of heat-resistant
masking tape is unavoidable, please make sure that the adhesives on the tape do not directly come in contact with the product.
●
When high-pressure shower cleaning is implemented, there is a possibility of exfoliation of the top electrodes caused by the water pressure stress so please avoid
the implementation.
●
If the implementation is unavoidable, then please evaluate the products beforehand.
For Surface Temperature Rise Graph see Environmental Applications. Additional environmental applications can also be found at www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
9/30/19
28
KOA Speer Electronics, Inc.
• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
[size=4] For those who work on power electronics software, there is usually not much code in this line, and it often takes several months to adjust a few lines of code, such as grid-connected algorith...
A 100W/200R cement resistor is connected to the J14 load. I checked the power meter and found that the load power is less than 1W. The voltage given by PC6 is 3.3V. The meter shows that there is a cur...
As shown in the figure, the wiring method of the bidirectional thyristor in the circuit is that because it is bidirectional, I swapped T2 and T1. The thyristor was always in the on state and could not...
First of all, I wish you all a happy Chinese New Year. This year can actually be described as "turbulent". Electronic technology and chips have become the top search terms in 2019. Every fluctuation i...
How to use NE555 to build a square wave signal with a duty cycle of 50%, a signal amplitude of -5V~+5V, and an adjustable frequency (1khz~50khz). I have only learned the basics of circuit analysis and...
As shown in the picture, the actual boost voltage of the ME2139 DC-DC boost IC I used is 4.8V, and the current it can withstand is 2.5A. There is a series heating wire (2.5R) in the COIL, and I connec...
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
