5962-9315502HYC datasheet, PDF

Datasheet> All Categories > storage> storage> 5962-9315502HYC

5962-9315502HYC: DescriptionEEPROM Module, 256KX8, 150ns, Parallel, CMOS,; Categorystorage storage; File Size3MB，939 Pages; ManufacturerMicrosemi; Websitehttps://www.microsemi.com

Download Datasheet Parametric View All

5962-9315502HYC Overview

EEPROM Module, 256KX8, 150ns, Parallel, CMOS,

5962-9315502HYC Parametric

Parameter Name	Attribute value
Maker	Microsemi
Reach Compliance Code	unknown
Maximum access time	150 ns
command user interface	NO
Data polling	YES
JESD-30 code	R-XDIP-T32
JESD-609 code	e4
length	40.64 mm
memory density	2097152 bit
Memory IC Type	EEPROM MODULE
memory width	8
Number of functions	1
Number of terminals	32
word count	262144 words
character code	256000
Operating mode	ASYNCHRONOUS
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
organize	256KX8
Package body material	UNSPECIFIED
encapsulated code	DIP
Encapsulate equivalent code	DIP32,.6
Package shape	RECTANGULAR
Package form	IN-LINE
page size	64 words
Parallel/Serial	PARALLEL
power supply	5 V
Programming voltage	5 V
Certification status	Not Qualified
Filter level	38535Q/M;38534H;883B
Maximum seat height	5.08 mm
Maximum standby current	0.01 A
Maximum slew rate	0.18 mA
Maximum supply voltage (Vsup)	5.5 V
Minimum supply voltage (Vsup)	4.5 V
Nominal supply voltage (Vsup)	5 V
surface mount	NO
technology	CMOS
Temperature level	MILITARY
Terminal surface	GOLD
Terminal form	THROUGH-HOLE
Terminal pitch	2.54 mm
Terminal location	DUAL
switch bit	NO
width	15.24 mm
Maximum write cycle time (tWC)	10 ms

Preview

Download Datasheet

View All

NOT MEASUREMENT

SENSITIVE

MIL-HDBK-103AP

6 MARCH 2014

SUPERSEDING

MIL-HDBK-103AN

12 SEPTEMBER 2013

DEPARTMENT OF DEFENSE

HANDBOOK

LIST OF STANDARD MICROCIRCUIT DRAWINGS

This handbook is for guidance only. Do not cite this document

as a requirement.

AMSC N/A

FSC 5962

MIL-HDBK-103AP

CONTENTS

PARAGRAPH

1.1

1.2

1.2.1

1.2.2

1.2.3

1.2.4

4.1

4.2

4.3

4.4

4.5

4.6

5.1

5.2

6.1

6.1.1

6.1.2

6.2

7.1

7.2

TABLE 1

SECTION 1

Part I

Part II

Part III

PAGE

SCOPE .......................................................................................................................................... 1

Purpose...................................................................................................................................... 1

Part or identifying number (PIN) ................................................................................................ 1

Drawing number......................................................................................................................... 1

Device class designator ............................................................................................................. 1

Case outline / lead finish ............................................................................................................ 2

Substitutability ............................................................................................................................ 2

APPLICABLE DOCUMENTS ......................................................................................................... 2

DEFINITIONS ................................................................................................................................ 2

REQUIREMENTS .......................................................................................................................... 2

Drawing requirements ................................................................................................................ 2

Preparation procedures ............................................................................................................. 2

Drawing effectivity and duration ................................................................................................. 2

Approved sources of supply....................................................................................................... 2

Radiation hardness assurance (RHA) levels ............................................................................. 2

Electrostatic discharge sensitivity (ESD) listing ......................................................................... 3

CONFIGURATION MANAGEMENT .............................................................................................. 3

Configuration management of SMDs ......................................................................................... 3

Record of users.......................................................................................................................... 3

DISTRIBUTION and REQUESTS .................................................................................................. 4

Distribution ................................................................................................................................. 4

Automatic distribution ................................................................................................................ 4

Electronic distribution ................................................................................................................. 4

Requests .................................................................................................................................... 4

NOTES .......................................................................................................................................... 4

Intended use .............................................................................................................................. 4

Subject item (key word) listing ................................................................................................... 4

Noun code descriptions ................................................................................................................. 5

Microcircuits................................................................................................................................... 12

Listed by SMD PIN .....................................................................................................................

Listed by generic PIN .................................................................................................................

714

Listed approved sources ............................................................................................................

932

Concluding material ...................................................................................................................

936

iii

MIL-HDBK-103AP

1.2.3 Case outline/lead finish. Case outline and lead finish are as described in each SMD. The lead finish indicated in the

section 1 Part I listing is the most readily available from the manufacturer listed for the part. The manufacturer is authorized to

supply other lead finishes than what is listed provided that further testing/qualification is performed by the manufacturer on the

other lead finish(es). The user needs to contact the manufacturer to determine the availability of other lead finishes not listed

herein.

1.2.4 Substitutability. Device-class-Q devices will replace device-class-M devices.

2. APPLICABLE DOCUMENTS This section is not applicable to the handbook.

3. DEFINITIONS This section is not applicable to the handbook.

4. REQUIREMENTS

4.1 Drawing requirements. SMD's will be prepared in accordance with ASME Y14.100 and DOD directives.

4.2 Preparation procedures. The procedures for the generation of an SMD are provided in MIL-HDBK-780.

4.3 Drawing effectivity and duration. SMD's and device class M one part - one part number SMDs which have become

inactive for new design are reflected in section 1, part 1 of the appendix of this document with an "I" in the status column.

4.4 Approved sources of supply. The approved sources of supply list in this handbook supersedes the approved sources

formerly listed in each individual SMD/DLA Land and Maritime Drawing. This handbook is the official list of approved sources

of supply for non-one part - one part number SMD PIN's and for device class M one part - one part number SMD PIN's. Device

classes B, S, Q, V, T, N (monolithic) and H, K, D, G, E (hybrid) one part - one part number SMD PIN's are listed for the

convenience of the users. Official listing for B, S, Q, V, T, N, H, K, D, G, and E levels are available in the applicable QML.

Manufacturers should notify DLA Land and Maritime-VA in writing if they no longer wish to be listed as an approved source of

supply for any device listed herein. This letter will be used by DSCC to remove the manufacturer from MIL-HDBK-103 for

those devices that the manufacturer specifies that he will no longer supply.

4.5 Radiation hardness assurance (RHA) levels. SMD devices which meet the RHA requirements of MIL-PRF-38535 or

MIL-PRF-38534 will be marked with the appropriate RHA designator M, D, P, L, R, F, G, or H replacing the dash (-) in the PIN

as indicated in the following example:

5962(M, D, P, L, R, F, G, or H)8999901EA

Only the highest RHA level for which the device is qualified will be listed in Section 1, Part I of the appendix of this document;

however, at the request of the customer, the manufacturer is authorized to supply any lower RHA level device. At the request

of the customer, the non-RHA PIN designated with a dash (-) may be supplied at the option of the manufacturer. The

manufacturer may also opt to submit a certificate of compliance to have the non-RHA PIN listed in addition to the RHA PIN in

Section 1, Part I of the appendix of this document.

Recommended Resources

The difference between monolithic capacitors and electrolytic capacitors

Even-numbered voltage doubler full-wave rectifier circuit d

LT1111 voltage flip mode circuit diagram

Three-phase AC phase sequence detection circuit

Field effect transistor low voltage oscillation circuit

Typical working principle diagram of HY8010 and HY8020 circuits

Signal linear transformation problem: [i=s]This post was last edited by Yanyuan Technology House on 2019-6-13 08:56[/i]Normally, the linear amplification of a small DC signal into a large signal can be achieved only through an amplifier c...; 燕园技术宅 Analog electronics

[GD32E231 DIY Contest] Part 4: Summary: Design name: Dynamic QR code displayWorks photos:Project Description: QR codes can be seen everywhere in life. They are used in various payment, collection, advertising, promotion, etc., because mobil...; muxb GD32 MCU

MSP430 microcontroller peripheral crystal oscillator design selection and reference solution: The MSP430 series of microcontrollers is a 16-bit ultra-low-power MSP430 microcontroller that Texas Instruments (TI) began to market in 1996. It is a mixed signal processor (Mixed Signal Processor) wi...; 火辣西米秀 Microcontroller MCU

【Gravity:AS7341 Review】+ Sensor Color Value Detection: [i=s]This post was last edited by jinglixixi on 2021-1-9 23:22[/i]After a period of exploration, the problem of using the color sensor was finally solved. In fact, in retrospect, it was not as difficu...; jinglixixi Domestic Chip Exchange

Schematic to PCB: When converting the schematic to PCB, the components are stacked together. Is there a shortcut key to separate them?...; tangwei8802429 PCB Design

[ESP32-Korvo Evaluation] (6) Preliminary evaluation of microphone array algorithm effect: What attracted me to the ESP-Korvo board is that it is equipped with a microphone array and the array algorithm can be freely used in the software (although it is not open source). In the previous pos...; cruelfox Domestic Chip Exchange

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components