CRCW0201 e3
www.vishay.com
Vishay
Lead (Pb)-free Commodity Thick Film Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Pure tin solder contacts on Ni barrier layer
provides compatibility with lead (Pb)-free and
lead containing soldering processes
• Metal glaze on high quality ceramic
• Material categorization: For definitions of compliance
please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER RATING
P
70
W
LIMITING
ELEMENT
VOLTAGE
U
max.
AC
RMS
/DC
V
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
MODEL
TOLERANCE
%
SERIES
± 200
± 0.5
- 200/+ 400
± 100
0.05
CRCW0201
0201
RR 0603M
- 200/+ 400
± 200
±5
- 200/+ 400
Zero-Ohm-Resistor:
R
max.
= 50 m,
I
max.
at 70 °C = 1.0 A
30
± 200
±1
10.0 to 10M
E96
1.0 to 9.76
47.0 to 1M
10.0 to 10M
1.0 to 9.76
10.0 to 10M
E24
1.0 to 9.1
E24; E96
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
TECHNICAL SPECIFICATIONS
PARAMETER
Rated Dissipation at 70 °C
(1)
Operating Voltage
U
max.
AC
RMS
/DC
Insulation Voltage
U
ins
(1 min)
Insulation Resistance
Operating Temperature Range
Weight
UNIT
W
V
V
°C
mg
CRCW0201
0.05
30
50
> 10
9
- 55 to + 155
0.17
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
Revision: 28-Oct-13
Document Number: 20052
1
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW02011K00FNED
C
R
C
W
0
2
0
1
1
K
0
0
F
K
E
D
MODEL
CRCW0201
VALUE
R
= Decimal
K
= Thousand
M
= Million
0000
= Jumper
TOLERANCE
D
= ± 0.5 %
F
= ± 1.0 %
J
= ± 5.0 %
Z
= Jumper
TCR
K
= ± 100 ppm/K
N
= ± 200 ppm/K
X
= - 200 ppm/K/+ 400 ppm/K
0
= Jumper
PACKAGING
ED
EE
EI
PRODUCT DESCRIPTION: CRCW0201 100 1K0 1 % ET7 e3
CRCW0201
MODEL
CRCW0201
100
TCR
± 200
ppm/K
± 100
ppm/K
- 200/+ 400
ppm/K
562R
RESISTANCE
VALUE
1R0
= 1
10R
= 10
1K0
= 1 k
10K
= 10 k
1M0
= 1 M
0R0
= Jumper
1%
TOLERANCE
VALUE
± 0.5 %
±1%
±5%
ET7
PACKAGING
ET7
EF4
ET2
e3
LEAD (Pb)-FREE
e3
= Pure tin
termination finish
PACKAGING
MODEL
CRCW0201
CODE
ED = ET7
EI = ET2
EE = EF4
QUANTITY
10 000
20 000
50 000
CARRIER TAPE
Paper tape acc.
to IEC 60068-3
Type I
WIDTH
8 mm
PITCH
2 mm
REEL DIAMETER
180 mm/7"
254 mm/10"
330 mm/13"
DIMENSIONS
in millimeters
SIZE
INCH
0201
METRIC
0603
L
0.6 ± 0.05
W
0.3 ± 0.05
DIMENSIONS
H
0.23 ± 0.05
T1
0.15 ± 0.05
T2
0.2
+ 0.05
- 0.10
SOLDER PAD DIMENSIONS
a
0.28
b
0.43
l
0.23
Note
• No marking for 0201 size.
Revision: 28-Oct-13
Document Number: 20052
2
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
DERATING
Fraction of Rated Dissipation
P
70
in %
Vishay
100
50
0
- 50
0
50
100
125
150
70
Ambient Temperature
ϑ
amb
in °C
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
4.5
4.7
IEC
60068-2
TEST
METHOD
-
-
PROCEDURE
TEST
Stability for product types:
CRCW0201 e3
Resistance
Voltage proof
-
U
= 1.4 x
U
ins
; 60 s
Solder bath method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(245 ± 5) °C
(3 ± 0.3) s
(20/- 55/20) °C and
(20/125/20) °C
9N
Depth 2 mm; 3 times
30 min. at - 55 °C;
30 min. at 125 °C
5 cycles
1000 cycles
4.23
4.23.2
4.23.3
4.23.4
4.23.5
4.23.6
4.23.7
-
2 (Ba)
30 (Db)
1 (Aa)
13 (M)
30 (Db)
-
Climatic sequence:
Dry heat
Damp heat, cyclic
Cold
Low air pressure
Damp heat, cyclic
DC load
-
125 °C; 16 h
55 °C;
90 % RH; 24 h; 1 cycle
- 55 °C; 2 h
1 kPa; (25 ± 10) °C; 1 h
55 °C;
90 % RH; 24 h; 5 cycles
U
=
P
70
x
R
U
max.
± (2 %
R
+ 0.1
)
± (0.5 %
R
+ 0.05
)
± (1 %
R
+ 0.05
)
1
to 10 M
± 0.5 %; ± 1 %; ± 5 %
No flashover or breakdown
Good tinning ( 95 % covered)
no visible damage
REQUIREMENTS
PERMISSIBLE CHANGE (R)
4.13
58 (Td)
Solderability
Good tinning ( 95 % covered)
no visible damage
± 100 ppm/K,
± 200 ppm/K,
- 200 ppm/K/+ 400 ppm/K
No visible damage
No visible damage,
no open circuit in bent position
± (0.5 %
R
+ 0.05
)
4.8.4.2
4.32
4.33
-
21 (Uu
3
)
21 (Uu
1
)
Temperature coefficient
Shear (adhesion)
Substrate bending
4.19
14 (Na)
Rapid change
of temperature
Revision: 28-Oct-13
Document Number: 20052
3
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
REQUIREMENTS
PERMISSIBLE CHANGE (R)
1
to 10 M
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
PROCEDURE
TEST
Stability for product types:
CRCW0201 e3
U
=
P
70
x
R
U
max.
;
1.5 h on; 0.5 h off;
4.25.1
-
Endurance at 70 °C
70 °C; 1000 h
70 °C; 8000 h
4.18.2
4.35
4.24
4.25.3
4.29
58 (Td)
-
78 (Cab)
-
45 (XA)
Resistance to
soldering heat
Flamability,
needle flame test
Damp heat, steady state
Endurance at upper
category temperature
Component
solvent resistance
Vibration, endurance
by sweeping
Solder bath method
(260 ± 5) °C; (10 ± 1) s
IEC 60695-11-5;
10 s
(40 ± 2) °C; (93 ± 3) % RH; 56 days
155 °C, 1000 h
Isopropyl alcohol;
50 °C; method 2
f = 10 Hz to 2000 Hz;
x, y, z
1.5 mm;
A
200 m/s
2
;
10 sweeps per axis
± (2 %
R
+ 0.1
)
± (4 %
R
+ 0.1
)
± (1 %
R
+ 0.05
)
No burning after 30 s
± (2 %
R
+ 0.1
)
± (2 %
R
+ 0.1
)
No visible damage
4.22
6 (Fc)
± (0.5 %
R
+ 0.05
)
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, environmental test procedures
Packaging of components is done in paper tapes according to IEC 60286-3.
Revision: 28-Oct-13
Document Number: 20052
4
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
