Automotive Relays
PCB Single Relays
Power Relay K (Open – Sealed)
n
n
n
n
Limiting continuous current 45A
Wide voltage range
24VDC coil versions available
For high current version refer to Power Relay K-S
Typical applications
ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump,
hazard warning signal, heated front screen, heated rear screen, ignition,
lamps front/rear/fog light, interior lights, main switch/supply relay, seat
control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter,
wiper control.
Contact Data
Typical applications
Contact arrangement
Rated voltage
Rated current
Limiting continuous current
23°C
85°C
Limiting making current
1)
Limiting breaking current
2)
Contact material
Min. recommended contact load
Initial voltage drop, at 10A, typ./max.
Operate/release time
Electrical endurance
Mechanical endurance, DC coil
1)
2)
3)
4)
5)
Resistive/inductive
loads
1 form A, 1 NO
12VDC
45A
45A
30A
100A
60A
AgNi0.15
Resistive/inductive
loads
1 form C, 1 CO
12VDC
A/B (NO/NC)
45/30A
45/30A
30/25A
100/30A
60/30A
AgNi0.15
Indicator lamps
1 form A, 1 NO
12VDC
30A
30A
25A
120A
3)
60A
AgSnO
2
Headlights,
capacitive loads
1 form A, 1 NO
12VDC
40A
40A
25A
180A
60A
AgSnO
2
Headlights
capacitive loads
1 form C, 1 CO
12VDC
A/B (NO/NC)
40/25A
40/25A
25/20A
180/60A
60/30A
AgSnO
2
>2x10
5
ops.
at 13.5VDC, 40A
1A at 5VDC
4)
20/300mV
typ. 5/3ms
5)
>2x10
5
ops.
>2.2x10
6
ops.
at 13.5VDC, 40A
up to 8x21W
>10
7
ops.
>10
5
ops.
up to 4x60W
>10
5
ops.
up to 4x60W
The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages.
For a load current duration of maximum 3s for a make/break ratio of 1:10.
Corresponds to a peak inrush current on initial actuation (cold filament).
See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/
For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher
risk of contact tack welding.
Max. DC load breaking capacity
TE0556-E
Load limit curve 1: arc extinguishes, during transit time (changeover contact).
Load limit curve 2: safe shutdown, no stationary arc (make contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
11-2011, Rev. 1111
www.te.com
© 2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
NOT the LATEST
REVISION
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
1
Automotive Relays
PCB Single Relays
Power Relay K (Open – Sealed)
(Continued)
Coil Data
Insulation Data
Rated coil voltage
Coil versions, DC coil
Coil
Rated
Operate
code
voltage
voltage
VDC
VDC
001
12
6.9
022
24
14.1
12VDC / 24VDC
Release
voltage
VDC
1.2
2.4
Coil
resistance
Ω±10%
90
362
Rated coil
power
W
1.6
1.6
Initial dielectric strength
between open contacts
between contact and coil
500VAC
rms
500VAC
rms
Other Data
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coils on request.
Coil operating range
TE0555-6
EU RoHS/ELV compliance
Ambient temperature, DC coil
Climatic cycling with condensation,
EN ISO 6988
Temperature cycling (shock),
IEC 60068-2-14, Na
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1
Damp heat constant,
IEC 60068-2-3, method Ca
Degree of protection, IEC 61810
compliant
-40 to +105°C
6)
3 cycles, storage 8/16h
20 cycles, -40/+85°C (dwell time 1h)
6 cycles, upper air temperature 55°C
56 days, upper air temperature 55°C
RT 0/II – open version
RT III – immersion cleanable version
Does not take into account the temperature rise due to the contact current
E = pre-energization
Corrosive gas,
IEC 60068-2-42
10 days
IEC 60068-2-43
10 days
Vibration resistance (functional),
Does not take into account
(sine pulse form),
IEC 60068-2-6
the temperature rise due to
acceleration, acc. to position
10 to 200Hz, 20 to 40g
7)
the contact current
Shock resistance (functional),
E = pre-energization
IEC 60068-2-27 (half sine form single pulses),
acceleration, acc. to position
8ms 30g
7)
Terminal type
PCB
Weight
sealed version
approx. 22g (0.77oz)
open version
approx. 19g (0.67oz)
Solderability (aging 3: 4h/155°C)
for leaded process (Tm = 183°C),
for Pb-free process (Tm = 217°C),
IEC 60068-2-20
Ta, method 1, hot dip 5s, 215°C
Storage conditions
according IEC 600688
8)
Packaging unit
sealed version
300 pcs.
open version
500 pcs.
6) See coil operating range DC.
7) No change in the switching state >10μs.
8) For general storage and processing recommendations please refer to our Application
Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/
Terminal Assignment (Open and Sealed Version)
Bottom view on solder pins
1 form A, 1 NO
1 form C, 1 CO
*) Terminal 4 to be bridged
TE1091-B1
TE1086-A1
2
11-2011, Rev. 1111
www.te.com
© 2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
Automotive Relays
PCB Single Relays
Power Relay K (Open – Sealed)
(Continued)
Dimensions
Power Relay K open version
18.6 ±0.65
23.3 ±0.7
8.5 ±0.2
18.0 ±0.5
9.2 ±0.4
Assembly and
positioning aid
3.4 ±0.1
3.4 ±0.1
21.1 ±0.4
Power Relay K sealed version
26.1 ±0.4
2.4 ±0.8
3.0 ±0.5 *)
*) additional tin tops
max. 1.5 mm
2.5 – 3.0
18.9 ±0.3
2.5 ±0.4
Terminals tinned
TE2179-42
21.2 ±0.3
2.5 – 3.0
0.55 ±0.25
Terminals tinned
3.0 ±0.5 *)
TE0579-I2
*) additional tin tops
max. 1.5 mm
Mounting Hole Layout
Bottom view on solder pins
Power Relay K open version
16.0 ±0.3
10.2 ±0.2
6.0 ±0.2
3.3 ±0.1
1.3 +0.1
2.4
5.4
1.0 +0.05
ø 2.3 +0.1
2.2 ±0.1
ø 2.1 +0.1
ø 2.3 +0.1
2.3 ±0.2
13.3 ±0.2
TE0575-K2
Power Relay K sealed version
16.0 ±0.3
10.2 ±0.2
6.0 ±0.2
ø 1.3 +0.1
3.4 ±0.6
6.6 ±0.3
12.1 ±0.1
3.3 ±0.1
ø 2.3 +0.1
2.2 ±0.1
ø 2.1 +0.1
12.1 ±0.1
1.0 +0.05
ø 2.3 +0.1
ø 2.3 +0.1
2.3 ±0.2
ø 2.3 +0.1
13.3 ±0.2
TE0580-L2
11-2011, Rev. 1111
www.te.com
© 2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
3
Automotive Relays
PCB Single Relays
Power Relay K (Open – Sealed)
(Continued)
Product code structure
V23076
Power Relay K, sealed
V23133
Power Relay K, open
Terminal
A
PCB
Design
1
Single relay
Coil
001
12VDC
Contact type
C
Single contact
Contact material
13
AgNi0.15
15
AgSnO
2
(Special)
Contact arrangement
2
1 form A, 1 NO
Type
Typical product code
V23076
-A
1
022
-C
13
3
3
022
D
14
3
Single relay
24VDC
Single contact
AgSnO
2
1 form C, 1 CO
V23076-A1001-C133
V23076-A1001-D143
V23076-A3001-C132
V23076-A3001-D142
V23076-A3001-D152
1)
V23076-A1022-C133
V23076-A1022-D143
V23076-A3022-C132
V23076-A3022-D142
V23133-A1001-C133
V23133-A1001-D143
V23133-A3001-C132
V23133-A3001-D142
V23133-A3001-D152
1)
V23133-A1022-C133
V23133-A1022-D143
V23133-A3022-C132
V23133-A3022-D142
V23133-A3022-D152
1)
1) For indicator lamps.
Product code
Terminal/Encl.
PCB, sealed
Single relay
Design
12VDC
Coil
Contact
Single
Cont. material Arrangement
AgNi0.15
AgSnO
2
AgNi0.15
AgSnO
2
AgSnO
2
special
AgNi0.15
AgSnO
2
AgNi0.15
AgSnO
2
AgNi0.15
AgSnO
2
AgNi0.15
AgSnO
2
AgSnO
2
special
AgNi0.15
AgSnO
2
AgNi0.15
AgSnO
2
AgSnO
2
special
1 form C, CO
1 form A, NO
1 form C, CO
1 form A, NO
1 form C, CO
1 form A, NO
1 form C, CO
1 form A, NO
Part number
1393277-4
1393277-6
1-1393277-4
1-1393277-7
1-1414175-0
1393277-8
1393277-9
1-1393277-8
1-1393277-9
1393278-7
1-1393278-3
5-1393278-7
5-1393278-9
1-1414173-0
3-1393278-7
3-1393278-9
7-1393278-1
7-1393278-2
1-1414174-0
24VDC
PCB, open
12VDC
24VDC
4
11-2011, Rev. 1111
www.te.com
© 2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
京公网安备 11010802033920号
EEWORLD
