New!
Fully illuminated pushbutton switches - bushing Ø 30 mm - momentary or latching
Distinctive features and specifications
FP series
K
Full actuator or symbol illumination
K
Suited for integrated designs
K
Large but lightweight
K
Pad printed or laser etched symbols
K
Snap-in and threaded bushing models
Pad printing
Laser
UG1410A
B2
Non-illuminated
Illuminated
ELECTRICAL SPECIFICATIONS
MATERIALS
• Max. current/voltage rating with resistive load :
- silver contacts (code 2) : 4A 12VDC
- gold plated contacts (code 4) : 200mA 12VDC
• Initial contact resistance : 50 mΩ max.
• Insulation resistance : 1 GΩ min. at 500VDC
• Dielectric strength : 1.000 Vrms 50 Hz min.
• Electrical life at full load :
- Momentary models : 1 million cycles (gold plated contacts)
400.000 cycles (silver contacts)
- Latching models : 200.000 cycles
GENERAL SPECIFICATIONS
• Case : PA46
• Actuator : PA12, gloss finish
• Bushing/ bezel : ABS, gloss finish
• Contacts :
Silver (code 2)
or silver, gold plated (code 4)
• Panel thickness :
- Snap-in version : 1,5 (.059) to 2 mm (.078) with panel gasket
2 (.078) to 2,5 mm (.885) without panel gasket
- Threaded bushing version : 1(.039) to 9 mm (.354) max.
• Total travel : 2,8 mm
± 0,5 mm
• Typical operating force : 8N
± 2N
• Low level or mechanical life :
- Momentary models : 1 million cycles
- Latching models : 200.000 cycles
• Torque : 2 Nm max. applied to nut
• Operating temperature : -40°C to +75°C
The company reserves the right to change specifications without notice.
B2-150
www.apem.com
APEM
FP series
New!
Fully illuminated pushbutton switches - bushing Ø 30 mm - momentary or latching
Overview
FP
SERIES
Actuator
Model
R
Round, curved
Electrical function
1
3
OFF - ON
Normally open
(NO)
A
B
C
D
E
1
Terminals
Solder lugs
C
D
Snap-in, dia. 30 mm
Threaded bushing,
dia. 30 mm
LED control & No of poles
Non-illuminated, 1 pole
Non-illuminated, 2 poles
Independent, 1 pole
Independent, 2 poles
Independent, 1 pole, dimming LED
B2
Contact mat.
2
4
Silver
Silver, gold
plated
1
2
3
4
5
6
7
9
Actuator colour
Blue
Black
Green
Grey
Yellow
Red
White/natural
Orange
1
2
3
4
5
6
7
8
Bezel colour
Blue
Black
Green
Grey
Yellow
Red
White/natural
Bright chrome
X
A
B
C
D
E
F
G
LED colour
Non-illum.
Blue
Green
Red
Yellow
White
Red/green
Red/blue
0
1
2
3
LED resistor
No resistor
supplied
12V resistor
24V resistor
48V resistor
Symbols
See end of series
Marking
X
1
2
No marking
Pad printing
Laser
ABOUT THIS SERIES
On the following pages, you will find successively :
model structure of switches and options in the same order as in above chart
Dimensions :
first dimensions are in mm while inches are shown as bracketed numbers.
: please note that not all combinations of above numbers are available.
Refer to the following pages for further information.
NOTICE
Mounting accessories
: Standard hardware supplied :1 panel gasket (snap-in versions)
1 plastic hex nut and 1 panel gasket (threaded bushing versions)
Packaging unit
: 20 pieces
APEM
www.apem.com
B2-151
New!
Fully illuminated pushbutton switches - bushing Ø 30 mm - momentary or latching
(1 Ø3
.20 0.
0D 5 0
IA /+0
0/+ .5
.01
9)
FP series
14.00
(.551)
To order a product, replace • with one of the codes selected under “LED control
and number of poles” on next page, then add he desired options.
B2
MODEL
STRUCTURE
Snap-in mounting - solder lug terminals
©
Flat
4.50
(.177)
Ø26.50
(1.043DIA)
00 )
4. IA
Ø3 39D
.3
(1
LATCHING
26.50
(1.043)
FPCR1•1
MOMENTARY
(
NO
)
OFF
-
ON
FPCR3•1
6.30
(.248)
0.50
(.020)
2.80
(.110)
Ø29.80
(1.173)
Mounting by threaded bushing - solder lug terminals
©
Flat
4.50
(.177)
Ø26.50
(1.043DIA)
00 )
4. IA
Ø3 39D
.3
(1
LATCHING
26.50
(1.043)
FPDR1•1
MOMENTARY
(
NO
)
OFF
-
ON
FPDR3•1
6.30
(.248)
0.50
(.020)
2.80
(.110)
Ø30.00x1.50 SI
(1.181DIAx1.50 IS)
WIRING DIAGRAM
POLE 2
+
LED
-
LED
POLE 1
B2-152
www.apem.com
APEM
New!
Fully illuminated pushbutton switches - bushing Ø 30 mm - momentary or latching
Options
LED RESISTOR
FP series
0
1
2
3
No resistor supplied
12V resistor
24V resistor
48V resistor
B2
MARKING
X
1
2
No marking
Pad printing
Laser
SYMBOLS
XX
No symbol
Ø
(.6 16
30 .00
DI
A)
©
Flat
©
Available symbols
See end of K-range, section D.
Marking colour
White marking for illuminated actuators (laser etching) and non-illuminated
black actuators (pad printing). Black marking for non-illuminated colour
actuators (pad printing). Other : on request.
Marking area
The symbol will be included in the hatched area.
(this is the optimal area, larger symbols can be made on request)
B2-154
www.apem.com
APEM
京公网安备 11010802033920号
EEWORLD
