Voltage Controlled Crystal Oscillator
Previous Vectron Model VVC4
VV-800
VV-800
Description
Vectron’s VV-800 Voltage Controlled Crystal Oscillator (VCXO) is a quartz stabilized square wave generator with a CMOS output. The VV-800 uses
fundamental crystals resulting in low jitter performance and a monolithic IC which improves reliability and reduces cost.
Features
•
CMOS output VCXO
•
Output Frequencies from 1.544 MHz to 77.760 MHz
•
5.0 or 3.3 V Operation
•
Fundamental Crystal Design with Low Jitter Performance
•
Output Disable Feature
•
Excellent 20ppm Temperature Stability
•
-10/70°C or -40/85°C Operating Temperature
•
Small Industry Standard Package, 3.2x5x1.2mm
•
Hermetically Sealed
•
Product is free of lead and compliant to EC RoHS Directive
Applications
•
SONET/SDH/DWDM
•
Ethernet, SynchE
•
xDSL, PCMIA
•
Digital Video
•
Broadband Access
•
Base Stations, Picocells
Block Diagram
V
DD
E/D or NC
Output
Crystal
Oscillator
V
C
E/D or NC
Page1
Gnd
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Performance Specifications
Table 1. Electrical Performance
Parameter
Voltage
1,
5V option
3.3V option
Current
2
, 5V option
3.3V option
Nominal Frequency
3
Pull Range
2,6
,
ordering option
Linearity
2
Gain Transfer
2,
61.440MHz
30.720MHz
Temperature Stability
Output Logic Levels
2
Output Logic High
Output Logic Low
Load
Rise Time
2,4
Fall Time
2,4
Symmetry
2
Period Jitter
5,7
, RMS (61.44 MHz)
Period Jitter
5,7
, Peak - Peak (61.44MHz)
Phase Noise
8
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
Control Voltage
Control Voltage Range for Pull Range
Control Voltage Input Impedance
“E” Ordering Option, +3.3V only
Control Voltage Modulation BW
Output Enable/Disable
9
Output Enabled
Output Disabled
Start-Up Time
Operating Temp, Ordering Option
Package Size
1]
2]
3]
4]
5]
6]
7]
8]
9]
Performance Specifications
Symbol
V
DD
I
DD
Frequency
f
N
APR
Lin
K
V
f
STAB
Outputs
V
OH
V
OL
I
OUT
t
R
t
F
SYM
фJ
фJ
45
50
3.0
23
-63
-97
-129
-144
-157
-159
-164
V
C
Z
IN
BW
V
IH
V
IL
T
SU
T
OP
0/70 or -40/85
5.0 x 3.2 x 1.2
0.5
0.3
2
10
0.9*V
DD
100
4.5
3.0
0.9*V
DD
V
0.1*V
DD
15
5
5
55
pF
ns
ns
%
ps
ps
dBc/Hz
1.544
±50, ±80, ±100
5
+80
+120
±20
77.760
MHz
ppm
%
ppm/V
ppm
Min
Supply
4.750
3.135
Typical
5.0
3.3
Maximum
5.250
3.465
25
15
Units
V
mA
V
KΩ
MΩ
kHz
V
0.1*V
DD
10
ms
°C
mm
The power supply should have by-pass capacitors as close to the supply and to ground as possible, for examples 0.1 and 0.01uF
Parameters are tested with production test circuit in Figure 1.
See Standard Frequencies and Ordering Information tables for more specific information
Measured from 20% to 80% of a full output swing (Fig 2).
Not tested in production, guaranteed by design, verified at qualification.
Tested with Vc = 0.3V to 3.0V unless otherwise stated in part description
Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples.
Phase Noise is measured with an Agilent E5052A.
The Output is Enabled if the Enable/Disable is left open.
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Page2
Test Circuit
t
R
0.8*V
DD
50%
15pF
0.2*V
DD
Waveform
t
F
I
DD
4
.1µF
.01µF
I
C
V
C
1
+
-
3
2
+
V
DD
-
On Time
Period
Fig 1: Test Circuit
Fig 2: Waveform
Table 2. Absolute Maximum Ratings
Parameter
Power Supply
Voltage Control Range
Storage Temperature
Soldering Temp/Time
Symbol
V
DD
V
C
TS
T
LS
Ratings
0 to 6
0 to V
CC
-55 to 125
260 / 20
Unit
V
V
°C
°C / sec
Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or
any other conditions in excess of conditions represented in the operational sections of this datasheet. Exposure to absolute maximum
ratings for extended periods may adversely affect device reliability. Permanent damage is also possible if OD or Vc is applied before Vcc.
Typical Phase Noise
Typical Gain
Typical Characteristics - Phase Noise and Gain Curve
VV-800 @ 61.44 MHz
150
100
90
100
80
70
60
Pull (ppm)
Vc (volts)
0
0
0.5
1
1.5
2
2.5
3
40
-50
30
20
10
-150
0
50
50
Gain (ppm/V)
Pull
Gain
-100
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Page3
Reliability
VI qualification includes aging at various extreme temperatures, shock and vibration, temperature cycling, and IR reflow
simulation. The VV-800 family is capable of meeting the following qualification tests:
Table 3. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Solderability
Gross and Fine Leak
Resistance to Solvents
Moisture Sensitivity Level
Contact Pads
Conditions
MIL-STD-883, Method 2002
MIL-STD-883, Method 2007
MIL-STD-883, Method 2003
MIL-STD-883, Method 1014
MIL-STD-883, Method 2015
MSL 1
Gold over Nickel
Handling Precautions
Although ESD protection circuitry has been designed into the VV-800 proper precautions should be taken when handling and
mounting. VI employs a human body model (HBM) and a charged device model (CDM) for ESD susceptibility testing and design
protection evaluation.
Table 4. ESD Ratings
Model
Human Body Model
Charged Device Model
Minimum
500V
500V
Conditions
MIL-STD-883, Method 3015
JESD22-C101
Table 5. Reflow Profile
Parameter
PreHeat Time
Ramp Up
Time Above 217 °C
Time To Peak Temperature
Time at 260 °C
Ramp Down
Symbol
t
S
R
UP
t
L
T
AMB-P
t
P
R
DN
Value
60 sec Min, 180 sec Max
3 °C/sec Max
60 sec Min, 150 sec Max
480 sec Max
20 sec Min, 40 sec Max
6 °C/sec Max
The device is qualified to meet the JEDEC standard for
Pb-Free assembly. The temperatures and time intervals
listed are based on the Pb-Free small body requirements.
The VV-800 device is hermetically sealed so an aqueous
wash is not an issue.
Termination Plating:
Electroless Gold Plate over Nickel Plate
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Page4
Outline Drawing & Pad Layout
6
5
4
XXMXXXX
VI YWW
.197±.005
(5±0.13)
1
2
3
.126±.005
(3.2±0.13)
.025
(0.64)
.079
(2.0)
.050
(1.27)
.100±.004
(2.54±.1)
1.2 Max
.035
(0.89)
.039±.006
(1.0±.15)
.074
(1.87)
.055
(1.41)
.050
(1.27)
.015
(0.38)
Dimensions in inches (mm)
Table 6. Pin Out
Pin
1
2
3
4
5
6
Symbol
V
C
E/D
GND
Output
E/D
Function
VCXO Control Voltage
Enable Disable or NC
Case and Electrical Ground
Output
Enable Disable or NC
Power Supply Voltage
V
DD
Tape & Reel (EIA-481-2-A)
Table 7. Tape and Reel Informattion
Tape Dimensions (mm)
Dimension
Tolerance
VV-800
Reel Dimensions (mm)
Po
Typ
4
W
Typ
12
F
Typ
5.5
Do
Typ
1.5
P1
Typ
8
A
Typ
178
B
Min
1.78
C
Typ
13
D
Min
20.6
N
Min
55
W1
Typ
12.4
W2
Max
22.4
# Per
Reel
500
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Page5
京公网安备 11010802033920号
EEWORLD
