EEWORLDEEWORLDEEWORLD

Part Number

Search

EKRG250ELL220ME07D

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 25V, 20% +Tol, 20% -Tol, 22uF,
CategoryPassive components    capacitor   
File Size262KB,2 Pages
ManufacturerUnited Chemi-Con
Websitehttp://www.chemi-con.com/
Environmental Compliance
Download Datasheet Parametric View All

EKRG250ELL220ME07D Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 25V, 20% +Tol, 20% -Tol, 22uF,

EKRG250ELL220ME07D Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerUnited Chemi-Con
package instruction,
Reach Compliance Codecompli
capacitance22 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter5 mm
dielectric materialsALUMINUM
length7 mm
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Package formRadial
method of packingBulk
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)25 V
ripple current46 mA
seriesKRG
Terminal pitch2 mm
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low profile, 105℃
KRG
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Series
Downsized
KRG
Downsized
Low profile
KMG
P142
・Low
profile :φ4×7mm toφ18×25mm
・Endurance
: 1,000 hours at 105℃
・Solvent
resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS
Compliant
KMA
P127
◆SPECIFICATIONS
Characteristics
-55 to +105℃
6.3 to 50V
dc
(at 20℃, 120Hz)
±20%
(M)
I=0.01CV or 3µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃ after 2 minutes)
Rated voltage (V
dc
)
6.3V 10V 16V 25V 35V 50V
tanδ (Max.)
0.28 0.24 0.20 0.16 0.14 0.12
When nominal capacitance exceeds 1,000µF, add 0.03 to the value above for each 1,000µF increase.
(at 20℃, 120Hz)
Rated voltage (V
dc
)
6.3V 10V 16V 25V 35V 50V
Z(-25℃)/Z(+20℃)
5
4
3
2
2
2
Z(-40℃)/Z(+20℃)
10
8
6
4
3
3
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 1,000 hours
at 105℃.
Rated voltage
6.3 to 16V
dc
25 to 50V
dc
Capacitance change
≦±25%
of the initial value
≦±20%
of the initial value
D.F. (tanδ)
≦200%
of the initial specified value
≦200%
of the initial specified value
Leakage current
≦The
initial specified value
≦The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 500 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage
6.3 to 16V
dc
25 to 50V
dc
Capacitance change
of the initial value
≦±25%
≦±20%
of the initial value
D.F. (tanδ)
≦200%
of the initial specified value
≦200%
of the initial specified value
Leakage current
≦The
initial specified value
≦The
initial specified value
Shelf Life
◆DIMENSIONS
[mm]
Terminal
Code : E
F
±
0.5
F
±
0.5
F
±
0.5
(
φ
12.5 to
φ
18)
φD'
φd
Sleeve (PET : Brown)
or
L'
Vent
(φ and larger)
10
15min.
4min.
( 4 to
φ
10)
φ
Gas escape end seal
8
4
6.3
10 & 12.5 16 & 18
φD
5
-
-
7L
0.45 0.45 0.45 -
φd
0.5 0.5 0.6
0.6
0.8
≧9L
-
5.0
7.5
F
1.5 2.0 2.5 3.5
φD
'
φD+0.5max.
L'
L+1.5max. (7L : L+1.0max.)
◆PART
NUMBERING SYSTEM
E KRG
AAA
E
AA AAA
M
AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10µF:100, 1,000µF:102)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3, 35V:350, 50V:500)
Series code
Category
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Please refer to "Product code guide (radial lead type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
130
CAT. No. E1001O
Tutorial on using PARAM in EDMA3
[i=s]This post was last edited by Jacktang on 2019-10-12 16:04[/i]OMAP-L138 is a dual-core heterogeneous processor combining ARM9 and C6000 from TI. The highest main frequency of ARM and DSP is 456MHz...
Jacktang Microcontroller MCU
Active filter circuit simulation
It is necessary to amplify the 50HZ industrial frequency signal. The following circuit (second-street active filter circuit) can filter out noise of other frequencies and obtain a good amplification e...
congcong3580 Analog electronics
How to control the harmonics of a 25W RF power amplifier to -80dBc?
136MHz-174MHz, 25W power amplifier chip outputs second harmonic -38dBc, with an elliptical low-pass filter (stopband suppression -56dB), output harmonic -55dbc, the index requirement is -80dBc, what m...
bao1231 RF/Wirelessly
Balancing ADC Size, Power, Resolution, and Bandwidth for Precision Data Acquisition Systems
[i=s]This post was last edited by qwqwqw2088 on 2021-12-24 08:41[/i]The trend toward smaller industrial products is creating new challenges for precision data acquisition systems. Designers must balan...
qwqwqw2088 Analogue and Mixed Signal
Why should we learn about transistor circuits when there are integrated circuits?
[i=s]This post was last edited by tiankai001 on 2018-12-7 09:05[/i] [b][size=5][color=#0000ff]1. Rapid development of circuit IC or LSI[/color][/size][/b][align=left][color=rgb(34, 34, 34)][font="]The...
tiankai001 Integrated technical exchanges
The old version of the forum homepage has a bug
RT, all garbled...
wsmysyn Suggestions & Announcements

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号