EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

PL5V1Z

Description
Zener Diode, 5.1V V(Z), 5.88%, 1W, Silicon, Unidirectional
CategoryDiscrete semiconductor    diode   
File Size74KB,1 Pages
ManufacturerBaneasa SA
Download Datasheet Parametric View All

PL5V1Z Overview

Zener Diode, 5.1V V(Z), 5.88%, 1W, Silicon, Unidirectional

PL5V1Z Parametric

Parameter NameAttribute value
MakerBaneasa SA
package instructionO-PALF-W2
Reach Compliance Codeunknow
ECCN codeEAR99
Shell connectionISOLATED
ConfigurationSINGLE
Diode component materialsSILICON
Diode typeZENER DIODE
JESD-30 codeO-PALF-W2
Number of components1
Number of terminals2
Package body materialPLASTIC/EPOXY
Package shapeROUND
Package formLONG FORM
polarityUNIDIRECTIONAL
Maximum power dissipation1 W
Certification statusNot Qualified
Nominal reference voltage5.1 V
surface mountNO
technologyZENER
Terminal formWIRE
Terminal locationAXIAL
Maximum voltage tolerance5.88%
Working test current80 mA
FPGA Design Practice (Logic)
FPGA Design Practice (Logic) is aimed at the vast number of FPGA/CPLD beginners. It explains FPGA/CPLD and related basic knowledge from scratch, and uses a motherboard-based learning kit that supports...
arui1999 Download Centre
SIMterix-Simplies~4~ Verilog
In the case of mixed integer and analog systems, simulation can only simulate Verilog or analog. If the digital part has only output, it is OK, just edit the voltage source and import the waveform fil...
xutong Analog electronics
[Repost] Discover Schottky diodes in life
[align=left][color=rgb(25, 25, 25)][font="]Our lives are full of technological products, such as televisions, refrigerators, computers, cars, solar street lights, etc. You have seen so many technologi...
皇华Ameya360 Power technology
For a 4-layer board, is it possible to lay ground on all 4 layers?
I have drawn a 4-layer board. Can I lay ground on all 4 layers? From the top layer to the bottom layer, they are Signal1, GND, Power, and Signal2 respectively, but the power layer has a thick power li...
小小金 PCB Design
About the selection of pull-up and pull-down resistors at A and B ends of 485 bus
[size=4]Question: About RS485[/size] [size=4]Use a resistor to pull up[/size] [size=4]B uses a resistor to pull down[/size] [size=4]A and B are connected by resistors, [/size] [size=4]What are the app...
Jacktang Analogue and Mixed Signal
6. [Learning LPC1768 library functions] Watchdog experiment
The purpose of the watchdog is to generate a reset when an error occurs in the microprocessor. When the watchdog is enabled, if the user does not feed the watchdog within the overflow period (reload t...
cxmdz NXP MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号