1272-5-31-1-1 datasheet, PDF - EEWORLD Datasheet

1272-5-31-1-1: DescriptionBoard Connector, 31 Contact(s), 1 Row(s), Male, Straight, 0.05 inch Pitch, Surface Mount Terminal, Receptacle; CategoryThe connector The connector; File Size107KB，1 Pages; ManufacturerConexcon Group; Environmental Compliance

Download Datasheet Parametric View All

1272-5-31-1-1 Overview

Board Connector, 31 Contact(s), 1 Row(s), Male, Straight, 0.05 inch Pitch, Surface Mount Terminal, Receptacle

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Conexcon Group
Reach Compliance Code	unknow
body width	0.1 inch
subject depth	0.15 inch
body length	1.55 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact point gender	MALE
Contact material	BRASS
contact mode	RECTANGULAR
Contact resistance	20 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	300VAC V
Durability	50 Cycles
Insulation resistance	1000000000 Ω
Manufacturer's serial number	1272
Plug contact pitch	0.05 inch
Installation method	STRAIGHT
Installation type	BOARD
Number of connectors	ONE
PCB row number	2
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	STAGGERED
PCB contact row spacing	3.0226 mm
Plating thickness	15u inch
Rated current (signal)	1 A
Guideline	UL
reliability	COMMERCIAL
Terminal pitch	2.54 mm
Termination type	SURFACE MOUNT
Total number of contacts	31

Computer power supply plus current regulation: I made a computer power supply with current regulation according to the information on the Internet, but the ic555 always burns out. Please help me take a look, thank you....; shanrenll Creative Market

Linear optocoupler isolation amplifier: Linear optocoupler isolation amplifier...; fighting Analog electronics

PCB design software Protel 99 SE and AD copper-free hole and copper-free slot design: Protel 99 SE and AD copper-free hole and copper-free slot design intuitive approach 1: Picture analysis, the pad wants to be made into a copper-free hole, but the pad is needed. Ask, why does the circ...; dengguoqiang PCB Design

Why is a bootstrap circuit used in BUCK power chip?: As shown in the figure, a general buck power chip has a BOOT capacitor, which actually forms a bootstrap circuit with a diode inside. The voltage obtained by charging C1 is used to power the MOS tube ...; lingking Power technology

The circuit observation room has changed: The current state of the circuit observation room is unbearable to look at. It is completely different from the original purpose of its establishment and it is not maintained. It is better to have few...; 不亦心 Suggestions & Announcements

The states of the terminal device in the TI ZigBee protocol stack involved in the protocol stack: In the C:\Texas Instruments\Z-Stack Home 1.2.2a.44539\Components\stack\zdo\ZDApp.h file of the Z-Stack Home 1.2.2a protocol stack, the different states of the device are defined as follows.typedef enu...; Jacktang Wireless Connectivity

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components