EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

SL1-026-UU130/01-77

Description
Board Connector, 26 Contact(s), 1 Row(s), Male, Right Angle Reverse, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size321KB,2 Pages
ManufacturerE-tec Interconnect Ltd.
Environmental Compliance
Download Datasheet Parametric View All

SL1-026-UU130/01-77 Overview

Board Connector, 26 Contact(s), 1 Row(s), Male, Right Angle Reverse, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

SL1-026-UU130/01-77 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerE-tec Interconnect Ltd.
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresROHS COMPLIANT
subject depth0.1 inch
body length2.6 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (15)
Contact completed and terminatedGold (Au)
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage500VAC V
Insulation resistance1000000000 Ω
Insulator colorBLACK
insulator materialPOLYBUTYLENE TEREPHTHALATE
JESD-609 codee4
Manufacturer's serial numberSL
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE REVERSE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.1 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts26
The op amp output noise contains the switching frequency of DCDC, but the power supply is actually very clean. How to improve it?
[i=s]This post was last edited by samyang13 on 2020-10-11 15:08[/i]Hello everyone, I recently tested the output of the PA78 amplifier, which is only used for DC amplification, but found that the rippl...
samyang13 Analog electronics
Wind power introduction
Wind power  Wind energy is usually referred to as the kinetic energy of air flow. Wind power generation is the conversion of the kinetic energy of air flow into electrical energy. Strong winds contain...
beh Industrial Control Electronics
AD Sampling Notes
[size=4]1: The reference voltage needs to be accurate enough. It is recommended to use an external high-precision reference voltage. [/size] [size=4]2: If the PGA is adjustable, the smaller the gain f...
Jacktang Microcontroller MCU
ISO 26262 Fault Tolerance Time Interval
I would like to share with you another important concept in functional safety - Fault Tolerant Time Interval (FTTI).Fault Tolerant Time Interval is a core concept in ISO 26262, and can also be called ...
Aguilera Microcontroller MCU
W806 Lianshengde 9.9 yuan development board experience 5 --- demo completed experience end
SPI-DMA has been added, and the speed is faster than before. The playability is still quite high even with a lower resolution. There is enough ROM and RAM space. However, the SDK peripheral drivers ne...
RCSN Domestic Chip Exchange
How can small household appliances support PD protocol fast charging? Why not add a PD power chip?
With the popularity of USB-C, there are more and more consumer PD chargers on the market. How can small household appliances also support PD protocol fast charging? Try adding a Lederui PD protocol po...
Legendary008 Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号