EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

L102021ML04BE

Description
SLIDE SWITCH, SPDT, LATCHED, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE, ROHS COMPLIANT
CategoryMechanical and electronic products    switch   
File Size317KB,6 Pages
ManufacturerC&K
Environmental Compliance  
Download Datasheet Parametric View All

L102021ML04BE Overview

SLIDE SWITCH, SPDT, LATCHED, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE, ROHS COMPLIANT

L102021ML04BE Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerC&K
package instructionROHS COMPLIANT
Reach Compliance Codecompli
ECCN codeEAR99
Actuator angle
Actuator colorBLACK
Actuator length0.335 inch
Actuator materialNYLON
Actuator typeHIGH TYPE
body width10.16 mm
Body colorBLACK
body height10.46 mm
Body length or diameter19.3 mm
center contact materialCOPPER ALLOY
Center contact platingGOLD OVER NICKEL
Contact (AC) maximum rated R load.02A@20VAC
Maximum contact current (AC)0.02 A
Maximum contact current (DC)0.02 A
Contact (DC) maximum rated power R load0.4VA@20VDC
Contact (DC) maximum rated R load.02A@20VDC
Contact resistance0.01 mΩ
Maximum contact voltage (AC)20 V
Maximum contact voltage (DC)20 V
Dielectric withstand voltage1000VRMS V
Electrical life10000 Cycle(s)
End contact materialCOPPER ALLOY
End contact platingGOLD OVER NICKEL
Insulation resistance1000000000 Ω
insulator materialNYLON
JESD-609 codee4
Manufacturer's serial numberL
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Number of positions1
Maximum operating temperature65 °C
Minimum operating temperature-30 °C
sealEPOXY TERMINAL SEALED
surface mountNO
Switch actionLATCHED
switch functionSPDT
Switch typeSLIDE SWITCH
Terminal surfaceGold (Au) - with Nickel (Ni) barrie
Terminal length0.256 inch
Terminal materialCOPPER ALLOY
Termination typeSOLDER
How do you calculate the current gain of this circuit?
How is this Io formula calculated? Doesn't the load need to be considered?...
幸福ing Analog electronics
Why does the LED not go out?
The 24V here is the sensor signal. When there is a signal, the LED will light up. But why is the LED still slightly bright when the 24V is completely disconnected? Is it because of static electricity?...
sky999 PCB Design
Brief Introduction of Ultra-Wideband (UWB) Development
1. Advantages of broadband technologyUltra-wideband technology, as one of the technologies of wireless personal area network, has many characteristics. First, it improves the utilization rate of the f...
兰博 RF/Wirelessly
LNA with step gain for W-CDMA (UMTS)
The MAX2645 SiGe low-noise amplifier (LNA) features 25dB gain steps, shutdown mode, and adjustable IP3. The LNA is optimized for WCDMA applications in the UMTS band (2110MHz-2170MHz). The MAX2645 feat...
JasonYoo RF/Wirelessly
Low-Cost Digital Thermometer Using a Single-Chip Microcontroller
In many applications, the ability to sense and display temperature is desirable or absolutely necessary. Temperature probes, thermostats, CPU monitors, and process control equipment are some of these ...
火辣西米秀 Microcontroller MCU
[GD32E503 Review] Simple Oscilloscope Experiment (Continued 2)
In order to improve the effect of the simple oscilloscope experiment, I tried to change the method of ADC conversion and graphic display. First, the ADC conversion and display were performed in segmen...
hujj Domestic Chip Exchange

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号