SV400M10A1SJ1019 datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> SV400M10A1SJ1019

SV400M10A1SJ1019: DescriptionAluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 400V, 20% +Tol, 20% -Tol, 10uF, Through Hole Mount, ROHS COMPLIANT; CategoryPassive components capacitor; File Size60KB，2 Pages; ManufacturerYAGEO; Websitehttp://www.yageo.com/; Environmental Compliance

Download Datasheet Parametric View All

SV400M10A1SJ1019 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 400V, 20% +Tol, 20% -Tol, 10uF, Through Hole Mount, ROHS COMPLIANT

SV400M10A1SJ1019 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	YAGEO
package instruction	,
Reach Compliance Code	compli
ECCN code	EAR99
capacitance	10 µF
Capacitor type	ALUMINUM ELECTROLYTIC CAPACITOR
dielectric materials	ALUMINUM (WET)
leakage current	0.25 mA
Manufacturer's serial number	SV
Installation features	THROUGH HOLE MOUNT
negative tolerance	20%
Number of terminals	2
Maximum operating temperature	105 °C
Minimum operating temperature	-25 °C
Package shape	CYLINDRICAL PACKAGE
method of packing	TAPE
polarity	POLARIZED
positive tolerance	20%
Rated (DC) voltage (URdc)	400 V
ripple current	120 mA
surface mount	NO
Delta tangent	0.2
Terminal shape	WIRE

Preview

Download Datasheet

View All

YAGEO CORPORATION

ALUMINUM ELECTROLYTIC CAPACITORS

Miniature Size Aluminum

Electrolytic Capacitors

[ For adapter and power supply applications

Series ]

105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications

ELECTRICAL CHARACTERISTICS

Operating Temperature : -40° ~ +105°C

Working Voltage :

160V

-25° ~ +105°C

450V

10 ~ 150µF

Rate Capacitance Range : 22 ~ 220µF

Capacitance Tolerance : -20 ~ +20%

DC Leakage Current (µA) : I = 0.06 CV + 10(µA)

whichever is greater.( After 2 minutes application of rated voltage at 25°C )

Dissipation Factor : at 120 Hz, 25°C

DESCRIPTION

Used in switching regulator applications in com-

puters. Especially for high frequency.

Low impedance and E.S.R., high permissible ripple

current at high frequency and higher operating

temperature (-40°C to +105°C).

WV (V) : 160

D.F (%) : 15

WV (V)

200

250

350

400

200

400

450

Impedance : Z - 25°C / Z + 20°C

Impedance : Z - 40°C / Z + 20°C

Load Life : After apply rated voltage with rated ripple current for 2000hrs at 105°C the capacitors

shall meet the following reuirements.

(a) Capacitance Change : Within 20% of Initial Value

(b) Dissipation Factor : Not Exceed 200% of Initial Requirement

Shelf Life : 1000 Hours, No Voltage Applied, at 105°C

(a) Capacitance Change : Within 20% of Initial Value

(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement

Frequency(Hz)

120

500

10K~100K

Temperature(°C)

Factor

2.10

1.70

105

1.00

DIAGRAM OF DIMENSIONS

Rubber Stand-off

Dø

4.0

5.0

Rubber End Seal

Dimensions : mm

1.5

2.0

2.5

3.5

5.0

dø

0.45

0.5

Vinyl Sleeve

(P.V.C)

Rubber End Seal

Vinyl Sleeve

(P.V.C)

15Min.

5Min.

D 0.5

0.4Max.

15Min.

5Min.

D 0.5

6.0

8.0

10.0

12.0

13.0

16.0

18.0

22.0

F 0.5

0.6

7.5

10.0

0.8

Recommended Resources

Bridge rectifier capacitor filter circuit

GPS RF front-end circuit diagram composed of MX2740

Automatic light control lighting circuit 2

Using autotransformer and time relay starting control

STK082G power amplifier circuit

Use operational amplifiers to form oscillator circuits and trigger circuits

【Deep Learning】Free technical documentation download｜Littelfuse Data Center Solutions Zone: Today’s data centers need to process massive amounts of data from millions of mobile devices and other items that make up the Internet of Things. To keep these facilities running properly, data center...; EEWORLD社区 Discrete Device

[Routine experience of the RVB2601 development board] Design of a peripheral CAN communication test board: This article has no tests, but designs the hardware expansion part and designs a peripheral CAN communication test board on the expansion port of the development board.1. Test board design picture2. P...; TL-LED XuanTie RISC-V Activity Zone

MOS tube heating abnormally, troubleshoot the cause to optimize equipment operation: [i=s]This post was last edited by Jacktang on 2019-2-13 19:52[/i] MOS tubes often heat up during circuit design, and the heating of MOS tubes indicates that it is operating incorrectly. In order to pr...; Jacktang Analogue and Mixed Signal

Design of control system for CNC engraving machine based on embedded system: From the processing principle, CNC engraving machine is a kind of drilling and milling combined processing. It is a typical mechatronics product and has a wide range of market applications in mold eng...; fish001 DSP and ARM Processors

PCB carries 10A current: 10A is the current of the relay output. Due to various reasons, the relay must be installed on the PCB board. I have no experience in designing 10A before. Method 1: Open a window in the solder mask l...; 15381807859 PCB Design

EEWORLD University ---- VICOR High Performance Power Conversion Seminar (2019.11): VICOR High Performance Power Conversion Seminar (2019.11) : https://training.eeworld.com.cn/course/5396...; hi5 Power technology

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components