Ordering Information .................................................................................................................................................................... 2
7.1. User Programming Interface ..................................................................................................................................... 19
7.2. Start-up output frequency and signaling types .......................................................................................................... 19
8.1. Any-frequency function ............................................................................................................................................. 20
9 I C/SPI Control Registers...................................................................................................................................................... 29
9.1. Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 29
9.2. Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 30
9.3. Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 31
9.4. Register Address: 0x03. Flac-N PLL Integer Value and Flac-N PLL Fraction MSW ................................................. 32
9.6. Register Address: 0x05. PostDiv, Driver Control ...................................................................................................... 33
9.7. Register Address: 0x06. mDriver, Driver Control ...................................................................................................... 34
2
10 I C Operation ........................................................................................................................................................................ 35
2
10.1. I C protocol ............................................................................................................................................................... 35
2
10.2. I C Timing Specification ............................................................................................................................................ 37
2
10.3. I C Device Address Modes ....................................................................................................................................... 38
Dimensions and Patterns ........................................................................................................................................................... 45
Additional Information ................................................................................................................................................................ 46
Revision History ......................................................................................................................................................................... 47
Rev 0.991
Page 3 of 47
www.sitime.com
SiT3521
1 to 340 MHz Elite™ I
2
C/SPI Programmable Oscillator
1 Electrical Characteristics
PRELIMINARY
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
1
-10
-20
-25
-50
First Year Aging
Operating Temperature Range
F_1y
T_use
–
-20
-40
-40
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
VIH
VIL
Z_in
DC
T_start
T_oe_hw
70%
–
–
45
–
–
Typ.
–
–
–
–
–
±1
–
–
–
3.3
3.0
2.8
2.5
–
–
100
–
–
–
Max.
340
+10
+20
+25
+50
–
+70
+85
+105
Supply Voltage
3.63
3.3
3.08
2.75
–
30%
–
55
3.0
3.8
V
V
V
V
Vdd
Vdd
kΩ
%
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
OE pin
OE pin
OE pin, logic high or logic low
Unit
MHz
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1 -year aging at 25°C
Extended Commercial
Industrial
Extended Industrial. Available only for I C operation, not SPI.
2
st
Condition
Factory or user programmable, accurate to 6 decimal places
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Frequency Range
Frequency Stability
Temperature Range
Input Characteristics – OE Pin
Output Characteristics
Startup and Output Enable/Disable Timing
T_oe_sw
–
–
6.5
µs
Rev 0.991
Page 4 of 47
www.sitime.com
SiT3521
1 to 340 MHz Elite™ I
2
C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
PRELIMINARY
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3V or 2.5V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3V or 2.5V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
The following article is from Analog Devices, author ADIHave you noticed that when comparing systems operating at different speeds, or looking at how a software-defined system handles signals of diffe...
When I use AD18 to draw a schematic, the following situation appears. I have been using AD14 for a long time and I am not used to it. Why does the point where the wires converge become like this? Can'...
I first determined the range of the turns ratio (0.3, the maximum input voltage is the drain peak voltage) based on the maximum withstand voltage of the primary-side MOS tube and the reverse withstand...
I would like to share with you a press release. The security issues mentioned in the article do require us to pay more attention.
Connected sports devices, desktop toys and medical wearables face new ...
Author: Joshua Zhu, ST engineer
Click to download the pdf document:Keywords: BlueNRG-1/-2, low crystalProblem: Customers often report that the board works fine but cannot measure the 32khz clock.
ST e...
Last time, I experienced the superposition effect of camera and UI on V853 development board, and realized the freedom of V853 development board camera with one click. This project refers to the proje...
Mitsubishi Q series PLC connected to CHNet-Q to achieve Ethernet communication configuration method
CHNet-Q is an economical Ethernet communication processor developed by Xingda Easy Con...[Details]
The self-driving car service scenes that often appear in science fiction movies are now happening in reality. Two weeks ago, Baidu's driverless taxi service Robotaxi officially opened for operation...[Details]
The Origin of the Oscilloscope Nobel Prize winner, German physicist KF Braun (Figure 1) invented the CRT oscilloscope in 1897 out of curiosity about physical phenomena. He applied an oscillating sign...[Details]
1) Use USB to UART to connect the Tx and Rx of UART Note: The onboard CMSIS-DAP virtual serial port cannot be used as an ISP 2) Let the chip enter ISP mode, press and hold the ISP button, an...[Details]
What are the causes of noise?
The best way to eliminate noise often depends on the source of the noise and the specific situation. Here are some common ways to reduce or eliminate noise:
...[Details]
According to the South China Morning Post, Zhou Zhiping, a professor at Peking University and a veteran in the semiconductor industry, said that it would take China at least "five to 10 years" to cat...[Details]
Today, iQOO's official Weibo account announced that the iQOO Pro new product launch conference will be held in Beijing on August 22, which means that the launch of iQOO Pro is officially on the agend...[Details]
The schematic diagram and PCB diagram of the tracking and obstacle avoidance remote control car based on STC15 drawn by Altium Designer are as follows: The microcontroller source program is as follo...[Details]
Fuel cell vehicles use hydrogen as fuel. Hydrogen reacts chemically with oxygen in the atmosphere, converting chemical energy into electrical energy through electrodes, and using electrical energy ...[Details]
1. Read the instructions carefully before use to clarify whether it is AC or DC dual-use. 2. The voltage of the measured circuit cannot exceed the value indicated on the clamp meter, otherwise it is ...[Details]
When measuring high-value resistance in the megohm range, the impedance value displayed by the E4980A Precision LCR Meter is much lower than the DC impedance of the device under test. How can I measu...[Details]
On September 8, the much-anticipated domestic shooting game "SYNCED" (SYNCED) was launched globally simultaneously. Intel provided driver optimization on the first day of game release and supported X...[Details]
As sustainable energy develops, we need bigger and better batteries. According to foreign media reports, scientists at the University of Queensland have developed a new type of battery that charges f...[Details]
According to foreign media reports, companies including General Motors, Ford, Google and solar manufacturers said on January 10 that they would cooperate to establish standards for expanding the use ...[Details]
1 Introduction Embedded Ethernet development is a very challenging job. After several months of study, I personally think there are roughly two ways. The first way is to first get familiar with ...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
