EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN2512K12R6DGT1

Description
RESISTOR, THIN FILM, 1 W, 0.5 %, 100 ppm, 12.6 ohm, SURFACE MOUNT, 2512, CHIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

PTN2512K12R6DGT1 Overview

RESISTOR, THIN FILM, 1 W, 0.5 %, 100 ppm, 12.6 ohm, SURFACE MOUNT, 2512, CHIP, ROHS COMPLIANT

PTN2512K12R6DGT1 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerVishay
package instructionSMT, 2512
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length6.579 mm
Package formSMT
Package width3.15 mm
method of packingTR
Rated power dissipation(P)2 W
Rated temperature70 °C
resistance12.6 Ω
Resistor typeFIXED RESISTOR
size code2512
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage200 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
Xun uses Yocto file system to develop QT file system for i.MX6ULL Terminator
Article Directory1External storage device (U disk, TF card) use2Network configuration3Touch test4Screen brightness (backlight)All the test programs in this section require the development board to hav...
遥寄山川 ARM Technology
Msp430F5438A interrupt
For the single-chip microcomputer system, interruption is a very important feature and is worth studying. Definition of an interrupt: When the need arises, the CPU temporarily stops the execution of t...
火辣西米秀 Microcontroller MCU
10 ways to dissipate heat from PCB!
[i=s]This post was last edited by btty038 on 2021-6-29 08:00[/i]For electronic devices, a certain amount of heat will be generated when working, causing the internal temperature of the device to rise ...
btty038 PCB Design
MSP430F5529 clock 25MHz setting method
The launchpad of MSP430F5529 is a development kit that TI gives away more frequently. At least everyone in our lab has one. Many people think it is slow. Indeed, compared with the speed of STM32F103 (...
火辣西米秀 Microcontroller MCU
The impact of intermittent power charging on battery life
The figure shows the change of current relative to time when the 24V power supply is charged at 27.6V. Since the battery status needs to be detected, charging is stopped every 30s and the battery stat...
轩辕默殇 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号