EEWORLDEEWORLDEEWORLD

Part Number

Search

MIC5264-2.6/2.6YML

Description
150mA μCap Dual LDO Regulator
CategoryPower/power management    The power supply circuit   
File Size330KB,11 Pages
ManufacturerMicrochip
Websitehttps://www.microchip.com
Environmental Compliance
Download Datasheet Parametric View All

MIC5264-2.6/2.6YML Overview

150mA μCap Dual LDO Regulator

MIC5264-2.6/2.6YML Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
package instructionHVSON,
Reach Compliance Codecompli
ECCN codeEAR99
Maximum drop-back voltage 10.5 V
Maximum drop-back voltage 20.5 V
Maximum input voltage5.5 V
Minimum input voltage2.7 V
JESD-30 codeS-XDSO-N10
JESD-609 codee3
length2.5 mm
Number of functions1
Output times2
Number of terminals10
Working temperatureTJ-Max125 °C
Operating temperatureTJ-Mi-40 °C
Maximum output current 10.15 A
Maximum output current 20.15 A
Maximum output voltage 12.678 V
Minimum output voltage 12.522 V
Nominal output voltage 12.6 V
Maximum output voltage 22.678 V
Minimum output voltage 22.522 V
Nominal output voltage 22.6 V
Package body materialUNSPECIFIED
encapsulated codeHVSON
Package shapeSQUARE
Package formSMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE
Peak Reflow Temperature (Celsius)260
Certification statusNot Qualified
Regulator typeFIXED POSITIVE MULTIPLE OUTPUT LDO REGULATOR
Maximum seat height0.95 mm
surface mountYES
Terminal surfaceMATTE TIN
Terminal formNO LEAD
Terminal pitch0.5 mm
Terminal locationDUAL
Maximum time at peak reflow temperature40
width2.5 mm
Base Number Matches1
MIC5264
150mA µCap Dual LDO Regulator
General Description
The MIC5264 is a dual 150mA LDO in tiny 2.5mm x
2.5mm MLF
®
packaging ideal for applications where cost
is the priority. The MIC5264 is ideal for any application in
portable electronics, including both RF and Digital
applications. With low output noise and high PSRR, the
MIC5264 is ideal for noise sensitive RF applications. While
the fast transient response and active shutdown circuitry
makes it well-suited for powering digital circuitry.
The MIC5264 has a 2.7V to 5.5V input operating voltage
range, making it ideal for operation from a single cell
lithium ion battery or fixed 3.3V and 5V systems. Each
LDO is completely independent and can be powered
independently, making it easier to use in distributed power
applications.
The MIC5264 offers low dropout voltage (210mV at
150mA), low output noise (57µVrms), high PSRR and
integrates an active shutdown circuit on the output of each
regulator to discharge the output voltage when disabled.
Data sheets and supporting documentation can be found
on Micrel’s web site at: www.micrel.com
Features
2.7V to 5.5V supply voltage.
Low 75µA quiescent current per LDO.
Tiny 2.5mm x 2.5mm MLF
®
package.
Low Noise – 57µVrms.
High PSRR – 60dB at 1kHz.
Low dropout voltage – 210mV at 150mA.
Stable with ceramic output capacitors.
Independent enable pins.
Fast transient response.
Active shutdown on both outputs.
Applications
Cellular Telephones
PDAs
GPS Receivers
Typical Application
MIC5264-xxYML
VIN 1
VIN 2
EN 1
EN 2
1µF
0.01µF
BYP1
GND
BYP2
0.01µF
-80
Power Supply
Rejection Ratio
50mA
OUT 1
OUT 2
1µF
1µF
Rx/Synth
Tx
RF
Transceiver
-70
-60
-50
-40
-30
100mA
150mA
RF Power Supply
-20 V
IN
= V
OUT
+ 1V
V
OUT
= 3.0V
-10 BYP = 0.1µF
C
OUT
= 1µF
0
0.01 0.1
1
10
100
FREQUENCY (kHz)
1000
MicroLeadFrame
and MLF are trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
May 2006
M9999-052406
(408) 955-1690
Mobile device battery voltage remote monitoring system based on MC20E
[i=s]This post was last edited by xinxiaojun on 2018-10-22 14:39[/i] [align=center]Mobile device battery voltage remote monitoring system based on MC20E[/align] [align=left] [color=#0000ff]Technical b...
xinxiaojun GD32 MCU
[NXP Rapid IoT Review] Week 5: DIY BLE_APP for NXP IoT: RGB Dimming Control
[align=left]After implementing DIY BLE_APP for NXP IoT Bluetooth scanning, connection and reading sensor data last week, this week we improved and completed the app end to write data to the NXP IoT de...
dwwzl RF/Wirelessly
Questions about vhdl testbench
How do I write a testbench for a module that has sub-modules under it? The module has been instantiated and mapped in the testbench, and stimulus has been added, but the simulated signal has no value....
刘123 FPGA/CPLD
The difference between OTL and OCL circuits
[1] Is the difference between the OTL and OCL circuits in the figure only whether there is a large capacitor at the output end? (Are the types of power switch tubes also different?) [2] In the OCL cir...
shaorc Analog electronics
[RVB2601 creative application development] + LCD screen display function expansion
The RVB2601 development board is equipped with an LCD display, which can be used to display information. The slightly insufficient part is that the routine only provides a picture display function, bu...
jinglixixi XuanTie RISC-V Activity Zone
QCA9531 and AR9342 support USB camera mini embedded AP module
If there is a product that can provide a WiFi hotspot after power-on and has a USB interface, after connecting to the UVC Camera (UVC Camera), for the terminal that successfully connects to the WiFi h...
natertech RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号