[i=s]This post was last edited by hzz592788 on 2021-1-4 14:32[/i]A big guy has already lit the lamp, so it's not appropriate for me to light it again. So I just rummaged through the box and found a sc...
[i=s]This post was last edited by Hot Ximixiu on 2021-7-25 11:14[/i]1. Development Board IntroductionRV-STAR is a RISC-V evaluation development board based on the GD32VF103 MCU. It provides resources ...
[i=s]This post was last edited by wenyangzeng on 2022-2-17 15:57[/i]【GD32L233C-START Review】(2) LPUART Serial TerminalFor the evaluation of GD32L233C-START, if you still use those non-low-power demo D...
[size=4][color=#000000][backcolor=white]The API can:[/backcolor][/color][/size] [size=4][color=#000000][backcolor=white]1. Can run in static internal SARAM[/backcolor][/color][/size] [size=4][color=#0...
[i=s]This post was last edited by bbxyliyang01 on 2019-10-12 21:19[/i]Day 1 Installation of PIC microcontroller compilation environment
There are relatively few introductory or learning materials ab...
The DE-15 interface of the LOTO oscilloscope provides various hardware resources. Here is an open source simple DIY expansion board PCB, which is compatible with any LOTO oscilloscope model. We will p...
1. Brief introduction of single chip microcomputer crystal oscillator
The crystal oscillator of the microcontroller is a component that generates the clock frequency required by the microcontro...[Details]
The AM radio is built around the 555 timer chip. The only active device (silicon, germanium, or other) is the LM555. Tuning is done by an inductor and capacitor, with the LM555 acting as an AM demo...[Details]
0 Introduction
The schedule management system refers to the automatic realization of prompts, playback, recording and other functions at a specified time, such as blowing the wake-up call in th...[Details]
Reentrant functions
In the design of real-time systems, it is often the case that multiple tasks call the same function. If this function is unfortunately designed to be a non-reentrant fun...[Details]
This application note describes how to use a low-cost digital potentiometer to implement up/down dimming control, saving power while improving efficiency.
introduce
In automotive an...[Details]
The MAX17502 is a high-efficiency, high-voltage, synchronous step-down DC-DC converter that operates over a 4.5V to 60V input voltage range and is designed for a wide range of applications. Ultra-w...[Details]
Use a multimeter to test the load cell Weighing sensors are widely used in industrial weighing (such as belt scales, floor scales, electronic scales, body scales, etc.), force detection, and tension ...[Details]
In the R&D, design, production and application of automotive parts, product testing and verification is an extremely important part. Verification tests are commonly used in the basic research, techno...[Details]
Simply put, the relay protection tester can output a certain amplitude of voltage and current, which can be AC or DC of any frequency within the allowable range, single-phase or three-phase, and ca...[Details]
Recently, the relevant person in charge of the Energy Conservation Division of the Energy Conservation and Technology Equipment Department of the National Energy Administration said on the issue of...[Details]
Saving energy is an urgent task for both consumers and businesses. However, for most electronic devices today, we cannot always know how much power they actually consume. Smart devices that ...[Details]
1. Cache classification and application scenarios Cache is a high-speed buffer memory between the memory and the CPU, which is divided into icache (instruction cache) and dcache (data cache). If the ...[Details]
MCU: STM8L051F3xx EEPROM Address: 0x00 1000 ~ 0x00 10FF, 256 Bytes Simple operation instructions: EEPROM is write-protected after power-on reset. When writing data to it, it is necessary to unlo...[Details]
EV wiring harness trends: a design revolution
The rise of electric vehicles (EVs) is a major force for innovation in automotive wiring.
Electric and hybri...[Details]