WRA-YMD-6W
＆
WRB-YMD-6W
Series
WIDE INPUT,ISOLATED & REGULATED Dual/Single Output DC/DC Converter
SELECTION GUIDE
Input
order code
Nominal
Voltage(VDC)
Range
Max*
Output
Current(MA)
Max
Min
Voltage
(VDC)
(%,Typ)
Efficiency
WRA0505YMD-6W
5
5
5
5
5
5
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
4.5-9.0
4.5-9.0
4.5-9.0
4.5-9.0
4.5-9.0
4.5-9.0
9.0-18.0
9.0-18.0
9.0-18.0
9.0-18.0
9.0-18.0
9.0-18.0
9.0-18.0
18.0-36.0
18.0-36.0
18.0-36.0
18.0-36.0
18.0-36.0
18.0-36.0
18.0-36.0
18.0-36.0
36.0-72.0
36.0-72.0
36.0-72.0
36.0-72.0
36.0-72.0
36.0-72.0
36.0-72.0
36.0-72.0
11
11
11
11
11
11
20
20
20
20
20
20
20
40
40
40
40
40
40
40
40
80
80
80
80
80
80
80
80
±600
±250
±200
1200
500
400
±600
±250
±200
1200
500
400
250
±600
±250
±200
1500
1200
500
400
250
±600
±250
±200
1500
1200
500
400
250
±60
±25
±20
120
50
40
±60
±25
±20
120
50
40
25
±60
±25
±20
150
120
50
40
25
±60
±25
±20
150
120
50
40
25
±5
±12
±15
5
12
15
±5
±12
±15
5
12
15
24
±5
±12
±15
3.3
5
12
15
24
±5
±12
±15
3.3
5
12
15
24
75
80
82
76
80
82
79
82
84
79
82
84
82
81
84
86
78
80
84
86
85
80
84
85
78
80
84
86
85
FEATURES
◆
RoHS compliant
◆
Efficiency up to 86%
◆
1"×1"DIP Package
◆
Wide temperature performance at full
WRA0512YMD-6W
WRA0515YMD-6W
WRB0505YMD-6W
WRB0512YMD-6W
WRB0515YMD-6W
WRA1205YMD-6W
WRA1212YMD-6W
WRA1215YMD-6W
WRB1205YMD-6W
WRB1212YMD-6W
WRB1215YMD-6W
WRB1224YMD-6W
WRA2405YMD-6W
WRA2412YMD-6W
WRA2415YMD-6W
6 Watt load,-40°C to 85°C
◆
UL 94V-0 package material
◆
No heatsink required
◆
Low ripple and good EMC Features
◆
Industry standard pinout
◆
Power sharing on output
◆
I/O Isolation 1500VDC
◆
Short Circuit Protection(
automatic recovery
)
◆
Metal case package
◆
MTBF>1000000 hours
WRB2403YMD-1500
WRB2405YMD-6W
WRB2412YMD-6W
WRB2415YMD-6W
WRB2424YMD-6W
WRA4805YMD-6W
WRA4812YMD-6W
WRA4815YMD-6W
WRB4803YMD-1500
MODEL SELECTION
①
②
③ ④
⑤
⑥
⑦
WRB 24 05 Y M D -6W(1200)
WRB4805YMD-6W
WRB4812YMD-6W
WRB4815YMD-6W
WRB4824YMD-6W
①Product
Series
②Input
Voltage
③Output
Voltage
④Wide
(2:1) Input Range
⑤Metal
Shield
⑥1"×1"DIP
Package
⑦Rated
Power(Output current)
*Input voltage can't exceed this value,or will cause the permanent damage.
DESCRIPTION
The WRA_YMD-6W& WRB_YMD-6W series are specially
designed for applications where a group of polar power
supplies are isolated from the input power supply in a
distributed power supply system on a circuit board.
These products apply to:
1) where the voltage of the input power supply is wide
range (voltage range ≤2:1);
2) where isolation is necessary between input and output
(isolation voltage ≤1500VDC);
3) where the regulation of the output voltage and the
output ripple noise are demanded.
OUTPUT SPECIFICATIONS
Parameter
Test conditions
Min.
Typ.
Max.
Units
Output power
Positive voltage accuracy
Negative voltage accuracy
Load regulation
Line regulation(at full load)
Temperature drift(Vout)
Output Ripple**
Output Noise**
Switching frequency
See above products program
Refer to recommended circuit
Refer to recommended circuit
From 10% to 100% full load
Input voltage from low to high
Refer to recommended circuit
20MHz Bandwidth
20MHz Bandwidth
100% Full load,input voltage range
0.6
±1.0
±3.0
±0.5
±0.2
6
±3.0
±5.0
±1.0
±0.5
±0.03
20
50
300
50
100
W
%
%
%
%
%/°C
MV p-p
MV p-p
Khz
* Dual output models unbalanced load (25/100%):±5%Max
* *Test ripple and noise by "parallel cable" method. See detailed operation instructions at Testing of Power
Converter section, application notes.
MICRODC reserves the copyright
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 1 of 3
WRA-YMD-6W
＆
WRB-YMD-6W
Series
TEMPERATURE CHARACTERISTICS
Parameter
Storage humidity range
NO-load power consumption
Operating temperature
Storage temperature
Lead temperature
Temp.rise at full load
Cooling
Case material
Short circuit protection
*
Case material
MTBF
Weight
1000
15
1.5mm from case for 10 seconds
15
Free air convection
Plastic(UL94-V0)
Continuous,automatic recovery
Aluminium alloy
K hours
g
-40
-55
500
85
125
300
TYPICAL CHARACTERISTICS
Min.
Typ.
Max.
95
Conditions
Units
%
MW
°C
°C
°C
°C
Temperature Derating Graph
*Supply voltage must be discontinued at the end of short circuit duration.
ISOLATION SPECIFICATIONS
Parameter
Isolation test voltage
Isolation resistance
Isolation capacitance
RECOMMENDED CIRCUIT
Min.
1500
1000
100
Test conditions
Flash tested for 1 minute and 1mA max
Test at Viso=500VDC
Input/Outpu
Typ.
Max.
Units
VDC
MΩ
pF
OUTPUT Graph
APPLICATION NOTE
1) Requirement on output load
In order to ensure the product operate efficiently and reliably, in addition to a max load (namely full
load), a minimum load is specified for this kind of DC/DC converter. Make sure the specified range of
input voltage is not exceeded, the minimum output load no less than 10% load. If the actual load is less
than the specified minimum load, the output ripple may increase sharply while its efficiency and reliability
will reduce greatly. If the actual output power is very small, please add an appropriate resistor as extra
loading, or contact our company for other lower output power products.
2) Recommended Circuit
All the WRA_YMD-6W & WRB_YMD-6W Series have been tested according to the following
recommended testing circuit before leaving factory. This series should be tested under load. Never be
tested under no load (see Figure 1).
If you want to further decrease the input/output ripple,you can increase capacitance properly or
choose capacitors with low ESR. However, the capacitance of the output filter capacitor must be proper.
If the capacitance is too big, a startup problem might arise. For every channel of output,provided the safe
and reliable operation is ensured,the greatest capacitance of its filter capacitor sees (Table 1). General:
Cin: 5V&12V
100μF
24V&48V
10μF-47μF
Cout: 10PF/100mA
3) Input current
When it is used in unregulated power supply,be sure that the fluctuating range of the power supply
and the rippled voltage do not exceed the module standard.Input current of power supply should afford
the startup current of this kind of DC/DC module (Figure 2).
General: Ip≤1.4*Iin-max
(VDC)
3.3
5
9
12
15
24
EXTERNAL CAPACITOR TABLE (TABLE 1)
Single Vout
Cout
Dual Vout
Cout
4) No parallel connection or plug and play
(μF)
2200
1000
680
470
330
220
(VDC)
±5
±9
±12
±15
_
_
(μF)
680
470
330
220
_
_
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 2 of 3
WRA-YMD-6W
＆
WRB-YMD-6W
Series
OUTLINE DIMENSIONS
＆
FOOTPRINT DETAILS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
Dual/Single Output
RECOMMENDED FOOTPRINT
Top view,grid:2.54mm(0.1inch)
diameter:1.00mm(0.039inch)
TUBE OUTLINE DIMENSIONS
Note:
Unit:mm[inch]
Pin section tolerances:±0.10mm[±0.004inch]
General tolerances:±0.25mm[±0.010inch]
FOOTPRINT DETAILS
Pin
1
2
3
4
5
Single
GND
Vin
+V0
NC
0V
Dual
GND
Vin
+V0
0V
-V0
Note:
Unit :mm[inch]
General tolerances:
±0.50mm[±0.020inch]
L=530mm[20.866inch] Tube Quantity: 19pcs
L=220mm[8.661inch]
Tube Quantity: 7pcs
When the environment temperature is higher than 71°C, the product output ower
71°
should be less then 60% of the rated power.
No parallel connection or plug and play.
Use dual output simultaneously, forbid opening output pin (0V) to use as single
output.
NC:No connection
Note:
1. The load shouldn't be less than 10%, otherwise ripple will increase dramatically.
2. Operation under 10% load will not damage the converter; However, they may not meet all specification listed.
3. All specifications measured at Ta=25
°
C, humidity<75%, nominal input voltage and rated output load unless
otherwise specified.
4. In this datasheet, all the test methods of indications are based on corporate standards.
5. Only typical models listed, other models may be different, please contact our technical person for more details.
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
E-mail:tech@microdc.cn
Website:http://www.microdc.cn
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 3 of 3
京公网安备 11010802033920号
EEWORLD
