PH1-NI2FC3321 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-NI2FC3321

PH1-NI2FC3321: DescriptionTransponder, FC/UPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-NI2FC3321 Overview

Transponder, FC/UPC Connector,

PH1-NI2FC3321 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	compliant
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body height	13.2 mm
Body length or diameter	84.1 mm
Communication standards	GR-253, OC-192, SONET
Connection Type	FC/UPC CONNECTOR
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1543 nm
Nominal optical power output	1.122 mW
minimum return loss	-27 dB

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

Do you know about the X-Class platform and XGS 8000/XGS 12000 image sensor?

Zero-crossing trigger circuit design based on thyristor

BD-811 electronic mousetrap circuit

Digital sine wave generator circuit

4-digit control keyboard circuit

Monitor negative supply circuits

Chapter 4: Use of Timers and PWM: As mentioned above, the YOC platform used by RVB2601 encapsulates peripheral functions. This makes it easier to use without having to worry about the underlying knowledge. However, the disadvantage is...; manhuami2007 XuanTie RISC-V Activity Zone

Ask an outrageous question, why do we need to use a resistor to form a discharge path for the capacitor to discharge?: I have an outrageous question. Why do we need to use resistors to form a discharge path for capacitors to discharge and consume the charge released by the capacitors? Some people say that if there is ...; 小太阳yy Switching Power Supply Study Group

An annular solar eclipse is coming. Have those in the annular eclipse zone seen it?: After the partial solar eclipse last year, an annular solar eclipse is coming again. Unfortunately, I am not in the annular eclipse zone, so I can only see a partial solar eclipse.Filmed by CCTV, borr...; chunyang Talking

How to set differential traces for high-speed USB positive and negative in AD16 PCB: How to set up differential traces for high-speed USB positive and negative in AD16 PCB?...; zttian PCB Design

Let's discuss the latest firmware repair and upgrade methods for TI chips: For embedded systems, the upgrade of the main control chip is becoming more and more important. After the product is launched, if there is a bug in the program or a new functional module needs to be a...; alan000345 TI Technology Forum

【Infineon XENSIV PAS CO2 sensor】Official data study: [i=s]This post was last edited by dql2016 on 2022-10-27 15:37[/i]This sensor requires a 12V power supply. While waiting for the power module, please read the official development information. Official...; dql2016 Sensor

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components