EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-MLPFC3565

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-MLPFC3565 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,

PH1-MLPFC3565 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1548 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Introduction to the mobile station development board: ultra-low power python board
First of all, I would like to thank @dcexpert for donating the development board. Here is a brief introduction of the board:pybL series development board, ultra-low power consumption, supports micropy...
高进 Talking
USB to JTAG
Why does Pingtouge RVB2601 choose STM32F103C8T6 for USB to JTAG conversion? It takes a long time to download the FLASH every time...
梦溪开物 XuanTie RISC-V Activity Zone
DSP28335 SCI communication problem summary and problem summary
It is inevitable to encounter some problems in the learning process. I hope that by writing these problems down, on the one hand, I hope that the masters can give me some advice; I also hope that this...
Jacktang DSP and ARM Processors
Beetle ESP32-C3 test (IV) IDF method to provide AP connection
You can use IDF to connect to Wi-Fi or provide Wi-Fi services as an AP. Although the service capabilities of ESP32-C3 are limited, you can use this method to allow clients to connect to the device and...
bigbat RF/Wirelessly
Several questions about 7S3P battery pack circuit
Several questions about 7S3P battery pack circuit 1. Figure 1 shows the activation circuit of the short-circuit B+ and P+ of the electronic group. Why should the positive control method be used for th...
QWE4562009 Automotive Electronics
MSP430G2553 clock system configuration
For the configuration of the clock system, a total of four registers are used: DCOCTL-DCO control register, BCSCTL1-basic clock control register 1, BCSCTL2-basic clock control register 2, BCSCTL3-basi...
火辣西米秀 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号