EEWORLDEEWORLDEEWORLD

Part Number

Search

MIC2211-PLYML

Description
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, DSO10
CategoryPower/power management    The power supply circuit   
File Size760KB,10 Pages
ManufacturerMicrochip
Websitehttps://www.microchip.com
Environmental Compliance
Download Datasheet Parametric View All

MIC2211-PLYML Overview

DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, DSO10

MIC2211-PLYML Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerMicrochip
package instruction3 X 3 MM, LEAD FREE, MLF-10
Reach Compliance Codecompliant
ECCN codeEAR99
Maximum drop-back voltage 10.25 V
Maximum drop-back voltage 20.42 V
Maximum input voltage5.5 V
Minimum input voltage2.25 V
JESD-30 codeS-XDSO-N10
JESD-609 codee3
length3 mm
Humidity sensitivity level2
Number of functions1
Output times2
Number of terminals10
Working temperatureTJ-Max125 °C
Working temperature TJ-Min-40 °C
Maximum output current 10.15 A
Maximum output current 20.3 A
Maximum output voltage 13.06 V
Minimum output voltage 12.94 V
Nominal output voltage 13 V
Maximum output voltage 22.754 V
Minimum output voltage 22.646 V
Nominal output voltage 22.7 V
Package body materialUNSPECIFIED
encapsulated codeHVSON
Package shapeSQUARE
Package formSMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE
Peak Reflow Temperature (Celsius)260
Certification statusNot Qualified
Regulator typeFIXED POSITIVE MULTIPLE OUTPUT LDO REGULATOR
Maximum seat height1 mm
surface mountYES
Terminal surfaceMATTE TIN
Terminal formNO LEAD
Terminal pitch0.5 mm
Terminal locationDUAL
Maximum time at peak reflow temperature40
width3 mm
MIC2211
Micrel, Inc.
MIC2211
Dual
µCap
LDO in 3mm
×
3mm MLF™
General Description
The MIC2211 is a dual
µCap
low dropout regulator. The first
regulator is capable of sourcing 150mA, while the second
regulator can source up to 300mA.
Ideal for battery operated applications, the MIC2211 offers 1%
accuracy, extremely low dropout voltage (80mV @ 100mA),
and extremely low ground current (only 48µA total). Equipped
with TTL logic compatible enable pins, the MIC2211 can be
put into a zero-off-mode current state, drawing no current
when disabled. Separate enable pins allow individual control
of each output voltage.
The MIC2211 is a
µCap
design, operating with very small
ceramic output capacitors for stability, reducing required
board space and component cost.
The MIC2211 is available in fixed output voltages in the
10-pin 3mm
×
3mm MLF™ leadless package.
Features
• Input voltage range: 2.25V to 5.5V
• Stable with ceramic output capacitor
• 2 LDO outputs:
• Output 1 - 150mA output current
• Output 2 - 300mA output current
• Low dropout voltage of 80mV @ 100mA
Ultra-low quiescent current of 48µA total (24µA/LDO)
• High output accuracy:
• +1.0% initial accuracy
• +2.0% over temperature
• Thermal shutdown protection
• Current limit protection
Tiny 10-pin 3mm
×
3mm MLF™ package
Applications
• Cellular phones
• Wireless modems
• PDAs
Typical Application
MIC2211-xxBML
VIN
OFF ON
VOUT1
VOUT2
1 F
Ceramic
1 F
V
I/O
V
CORE
Baseband
Processor
EN1
EN2
CBYP
OFF ON
0.01 F
GND
MIC2211 Typical Cell Phone Application
MicroLeadFrame
and MLF are trademarks of Amkor Technology, Inc.
Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
October 2005
1
M9999-101805
MAX40026 280ps High-Speed Comparator
I would like to ask which expert has used this high-speed comparator and can give me some advice on PCB layout. Thank you....
guitianxia Automotive Electronics
A novice asks for advice on the MSP430 interrupt flag PxIFG
[i=s]This post was last edited by baqs603 on 2021-8-5 10:32[/i]Recently, when I was learning about the debouncing of mechanical buttons of MSP430, there was a sentence in the book that I didn't quite ...
baqs603 TI Technology Forum
What is 5G Super Uplink?
Favorite UplineThe most anticipated thing in the 5G era is the unprecedented improvement in the network's uplink capabilities.In the past, the Internet and mobile Internet era were mainly oriented tow...
btty038 RF/Wirelessly
Outsourcing of small brushless sensor driver
There is a small project that needs to be outsourced. General description: Drive 6-slot 4-pole inductive brushless motor, voltage: 6-18V, power 150W, over-current, under-voltage, stall protection. Spe...
andy1gao Motor Drive Control(Motor Control)
Single-ended forward converter
Why does the voltage of the MOS tube of a single-ended forward converter change to 2Vin first when the switch is turned off, and then change to Vin after a period of time? My understanding is that whe...
都是一个意思 Analog electronics
Bootloader issue of CH579
I would like to ask the experts, I am using CH579, and there are two things I don't understand about the Bootloader. 1. Method 1, address: https://en.eeworld.com/bbs/thread-1154663-1-1.html, if you up...
水上的浮尘 Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号