Shelf product is a high-performance CMOS static RAM
organized as 524,288 words by 8 bits. Easy memory expansion
is provided by an active LOW Chip Enable (E), an active LOW
Output Enable (G), and three-state drivers. This device has a
power-down feature that reduces power consumption by more
than 90% when deselected
.
Writing to the device is accomplished by taking Chip Enable
one (E) input LOW and Write Enable (W) inputs LOW. Data on
the eight I/O pins (DQ
0
through DQ
7
) is then written into the
location specified on the address pins (A
0
through A
18
). Reading
from the device is accomplished by taking Chip Enable one (E)
and Output Enable (G) LOW while forcing Write Enable (W)
HIGH. Under these conditions, the contents of the memory
location specified by the address pins will appear on the I/O pins.
The eight input/output pins (DQ
0
through DQ
7
) are placed in a
high impedance state when the device is deselected (E) HIGH),
the outputs are disabled (G HIGH), or during a write operation
(E LOWand W LOW).
Clk. Gen.
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
Pre-Charge Circuit
Row Select
Memory Array
1024 Rows
512x8 Columns
I/O Circuit
Column Select
Data
Control
CLK
Gen.
A10
A11
A12
A13
A14
A15
A16
A17
A18
DQ
0
- DQ
7
E
W
G
Figure 1. UT9Q512 SRAM Block Diagram
2
DEVICE OPERATION
A0
A1
A2
A3
A4
E
DQ0
DQ1
V
DD
V
SS
DQ2
DQ3
W
A5
A6
A7
A8
A9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
NC
A18
A17
A16
A15
G
DQ7
DQ6
V
SS
V
DD
DQ5
DQ4
A14
A13
A12
A11
A10
NC
The UT9Q512 has three control inputs called Enable 1 (E), Write
Enable (W), and Output Enable (G); 19 address inputs, A(18:0);
and eight bidirectional data lines, DQ(7:0). E Device Enable
controls device selection, active, and standby modes. Asserting
E enables the device, causes I
DD
to rise to its active value, and
decodes the 19 address inputs to select one of 524,288 words in
the memory. W controls read and write operations. During a read
cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
1
X
1
0
W
X
0
1
1
E
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
Figure 2. UT9Q512 25ns SRAM Pinout (36)
(For both packages)
PIN NAMES
A(18:0)
DQ(7:0)
E
W
G
V
DD
V
SS
Address
Data Input/Output
Enable
Write Enable
Output Enable
Power
Ground
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W greater than V
IH
(min) and E less than V
IL
(max) defines a read cycle. Read access time is measured from
the latter of Device Enable, Output Enable, or valid address to
valid data output.
SRAM Read Cycle 1, the Address Access in figure 3a, is
initiated by a change in address inputs while the chip is enabled
with G asserted and W deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as Device
Enable and Output Enable are active, the address inputs may
change at a rate equal to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable - Controlled Access in
figure 3b, is initiated by E going active while G remains asserted,
W remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQ(7:0).
SRAM read Cycle 3, the Output Enable - Controlled Access in
figure 3c, is initiated by G going active while E is asserted, W
is deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
3
WRITE CYCLE
A combination of W less than V
IL
(max) and E less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when W is less
than V
IL
(max).
Write Cycle 1, the Write Enable - Controlled Access in figure
4a, is defined by a write terminated by W going high, with E
still active. The write pulse width is defined by t
WLWH
when the
write is initiated by W, and by t
ETWH
when the write is initiated
by E. Unless the outputs have been previously placed in the high-
impedance state by G, the user must wait t
WLQZ
before applying
data to the nine bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable - Controlled Access in figure
4b, is defined by a write terminated by E going inactive. The
write pulse width is defined by t
WLEF
when the write is initiated
by W, and by t
ETEF
when the write is initiated by the E going
active. For the W initiated write, unless the outputs have been
previously placed in the high-impedance state by G, the user
must wait t
WLQZ
before applying data to the eight bidirectional
pins DQ(7:0) to avoid bus contention.
TYPICAL RADIATION HARDNESS
Table 2. Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
50
<1E-8
krad(Si)
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 90% worst case particle environment, Geosynchronous orbit, 0.025 mils of
Aluminum.
4
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.5 to 7.0V
-0.5 to 7.0V
-65 to +150°C
1.0W
+150°C
10°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
[align=left][font=微软雅黑, "][size=14px][color=#000000]3. Extended Kalman Filter[/color][/size][/font][/align] [align=left][font=微软雅黑, "][size=14px][color=#000000]Kalman filter is to obtain the dynamic e...
Introduction to IoTThe Internet of Things is a large network where any computer or almost anything with an IP address is connected to the internet or to each other to automate tasks or limit human int...
Live Broadcast IntroductionNanoEdge AI studio is a software tool that can help users automatically generate AI models. It does not require users to have professional knowledge in the field of AI. It o...
eric_wangST Sensors & Low Power Wireless Technology Forum
The event is in progress, welcome to join the board-playing team~
Activity link: You play the board and I will give you a prize! Pull out the board and play together@dcexpert"Playing with the Board" +...
1. Sensor Usage
There are many sensors on the Xingkong board, including sound sensors, light sensors, and motion sensors.
The use of these sensors requires the use of the pinpong library, which is man...
First, we download the IDF tool from the official website https://docs.espressif.com/projects/esp-idf/zh_CN/stable/esp32s3/get-started/windows-setup.html#get-started-windows-tools-installer.
Open the ...
This article introduces the computer voice system composed of Flash single-chip microcomputer AT89C2051 and digital voice chip ISD2560. The hardware circuit of the system is designed, and the practica...[Details]
1. Introduction
Electronic Stability Program (ESP) is an important part of modern automobile safety systems. It monitors the vehicle's motion status in real time and automatically adjusts the ...[Details]
Due to the purpose, use environment, production history and other reasons of TV, audio and video integrated circuits, they are not only complicated in model specifications, but also in packaging fo...[Details]
Core Tips: According to foreign media reports, on July 15 local time, Karamba Security, a leader in automotive and enterprise edge network security, announced that it had signed a production licens...[Details]
Central air conditioning is an indispensable facility for modern buildings, hotels, and shopping malls. It can bring people spring-like warmth and comfort every day. Due to the high power and energ...[Details]
An oscilloscope is a must-have for anyone who designs, manufactures, or repairs electronic equipment. In today's fast-paced world, engineers need the best tools to quickly and accurately solve measur...[Details]
Gartner's latest research shows that China's enterprise digital transformation and industry modernization have put forward new requirements for the use of cloud computing. China's infrastructure and ...[Details]
1) First set the fuse bit and turn on the JTAG function, as shown below. Use the USB ISP downloader to write the fuse. 2) Hardware Connection (a) One end of the 10-core cable is connected to the JT...[Details]
Microwave radiometer is a microwave receiver that uses microwaves for remote sensing and thus detects ground objects. It is widely used in detecting the atmosphere, ocean, vegetation and soil. As a...[Details]
JPMorgan analyst Samik Chatterjee predicted in a report on Monday that Apple will launch a cheaper 5G iPhone SE in the first half of 2022, which may be priced at around $399, and will sell about 30 m...[Details]
Recently, the Industrial Internet Consortium (IIC) released a white paper on best practices for developing and deploying IIoT solutions. The new white paper released by the Industrial Internet Conso...[Details]
Industry leaders are breaking down barriers to make it easy for developers to train and deploy advanced AI models on Windows 11 and deliver energy-efficient inference on RTX-equipped PCs and workstat...[Details]
SoftBank's ARM listing journey has been full of twists and turns. According to people familiar with the matter, due to the recent political turmoil in the UK, SoftBank Group has suspended negotiation...[Details]
Normally, when developing and debugging a DSP system, an SRAM chip is required as an off-chip program RAM. During debugging, the corresponding simulation board is used to download the program to th...[Details]
Basic diagram Working waveform of each pin of the switch tube Assuming that the amplification factor of Q1 is A and the base drive current is B, when the current of L T2A (that is, the collecto...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
