VC-801
CMOS Crystal Oscillator
Previous Vectron Model VCC4
VC-801
Description
Vectron’s VC-801 Crystal Oscillator (XO) is a quartz stabilized square wave generator with a CMOS output. The VC-801 uses fundamental or 3rd
overtone crystals resulting in very low jitter performance, and a monolithic IC which improves reliability and reduces cost.
Features
•
•
•
•
•
•
•
•
•
CMOS output XO
Output Frequencies from 32.768kHz to 125.000MHz
5.0, 3.3, 2.5 or 1.8 V Operation
Low Jitter Performance
Output Disable Feature
Excellent 20ppm temperature stability
-10/70°C, -20/70°C, -40/85°C or -55/125°C operating temperature
Small Industry Standard Package, 3.2x5.0x1.3mm
Product is compliant to RoHS directive
and fully compatible with lead free assembly
•
•
•
•
•
•
•
Applications
SONET/SDH/DWDM
Ethernet, GE, SynchE
Storage Area Networking
Fiber Channel
Digital Video
Broadband Access
Base Stations, Picocells
Block Diagram
V
DD
Output
Crystal
Oscillator
E/D
Page1
GND
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Table 1. Electrical Performance, 5V Option
Parameter
Voltage
1
Max Voltage
Current
2
≤20.000MHz
20.001 to 50.000MHz
50.001 to 75.000MHz
Current, Output Disabled
Speci cations
Performance Speci cations
Symbol
V
DD
I
DD
10
30
40
30
Frequency
f
N
1.544
Outputs
75.000
±20, ±25, ±32, ±50, ±100
mA
mA
mA
uA
MHz
ppm
Min
Supply
4.5
-0.7
Typical
5.0
Maximum
5.5
7
Units
V
V
Nominal Frequency
3
Stability
4
, (Ordering Option)
Output Logic Levels
2
Output Logic High
Output Logic Low
Output Logic High Drive
Output Logic Low Drive
Load
Output Rise /Fall Time
2
<20.000MHz
20.000 to 50.000MHz
50.001 to 75.000MHz
Output Leakage, Output Disabled
Duty Cycle
2,5
Period Jitter
6
RMS
Peak-Peak
RMS Jitter, 12kHz-20MHz
Output Enable/Disable
7
Output Enable
Output Disable
Disable time
Enable Internal Pull-Up Resistor
Start-Up Time
Operating Temp, (Ordering Option)
1]
2]
3]
4]
5]
6]
7]
V
OH
V
OL
I
OH
I
OL
I
OUT
t
R
/t
F
0.9*V
DD
0.1*V
DD
16
16
15
8
5
2
V
V
mA
mA
pF
ns
ns
ns
uA
%
ps
ps
I
Z
45
фJ
3.0
21
фJ
Enable/Disable
V
IH
V
IL
t
D
100
t
SU
T
OP
4.0
0.5
50
±10
55
1
ps
0.8
100
8
-10/70, -20/70, -40/85, -55/125
V
V
ns
Kohm
ms
°C
The power supply should have by-pass capacitors as close to the supply and to ground as possible, for example 0.1 and 0.01uF.
Parameters are tested a test circuit shown in Figure 1.
See Standard Frequencies and Ordering Information tables for more speci c information.
Includes initial accuracy, operating temperature, supply voltage, shock and vibration (not under operation) and aging for 50 and 100ppm options.
Duty Cycle is measured as On Time/Period, see Fig 2.
Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples, see Application Note for Typical Phase Noise and Jitter Performance.
The Output is Enabled if the Enable/Disable is left open.
t
R
I
DD
+
V
DD
4
.1µF
.01µF
1
+
Period
Fig 1: Test Circuit
Page2
t
F
V
OH
3
2
15pF
50%
V
OL
On Time
Fig 2: Waveform
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Speci cations
Performance Speci cations
Table 2. Electrical Performance, 3.3V Option
Parameter
Voltage
1
Maximum Voltage
Current
2
32.768kHz to 1.499MHz
1.500 to 20.000MHz
20.001 to 50.000MHz
50.001 to 100.000MHz
100.001 to 125.000MHz
Current, Output Disabled
Frequency
Nominal Frequency
3,8
Stability
4
, (Ordering Option)
Outputs
Output Logic Levels
2
Output Logic High
Output Logic Low
Output Logic High Drive
Output Logic Low Drive
Load
Output Rise /Fall Time
2
32.768kHz to 345.6kHz
345.6kHz to 20.000MHz
20.001 to 50.000MHz
50.001 to 75.000MHz
75.001 to 125.000MHz
Output Leakage, Output Disabled
Duty Cycle
2
,
5
Period Jitter
6
RMS
Peak-Peak
RMS Jitter, 12kHz-20MHz
Output Enable/Disable
7
Output Enable
Output Disable
Disable time
Enable Internal Pull-Up Resistor
Start-Up Time
Operating Temp, (Ordering Option)
1]
2]
3]
4]
5]
6]
7]
8]
Symbol
V
DD
I
DD
Min
Supply
2.97
-0.5
Typical
3.3
Maximum
3.63
5
5
7
20
30
40
30
Units
V
V
mA
mA
mA
mA
mA
uA
MHz
ppm
f
N
1
125.000
±20, ±25, ±32, ±50, ±100
V
OH
V
OL
I
OH
I
OL
I
OUT
t
R
/t
F
0.9*V
DD
0.1*V
DD
8
8
15
200
6
4
3
2
V
V
mA
mA
pF
ns
ns
ns
ns
ns
uA
%
ps
ps
I
Z
45
фJ
3.0
21
фJ
Enable/Disable
V
IH
V
IL
t
D
100
t
SU
T
OP
2.0
0.5
50
±10
55
1
ps
0.5
100
8
-10/70, -20/70, -40/85, -55/125
V
V
ns
Kohm
ms
°C
The power supply should have by-pass capacitors as close to the supply and to ground as possible, for example 0.1 and 0.01uF.
Parameters are tested a test circuit shown in Figure 1.
See Standard Frequencies and Ordering Information tables for more speci c information.
Includes initial accuracy, operating temperature, supply voltage, shock and vibration (not under operation) and aging for 50 and 100ppm options.
Duty Cycle is measured as On Time/Period, see Fig 2.
Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples, see Application Note for Typical Phase Noise and Jitter Performance.
The Output is Enabled if the Enable/Disable is left open.
Continuous frequency range is 1-125 MHz. 32.768 kHz is also available.
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Page3
Speci cations
Performance Speci cations
Table 3. Electrical Performance, 2.5V Option
Parameter
Voltage
1
Maximum Voltage
Current
2
32.768kHz to 1.499MHz
1.500 to 20.000MHz
20.001 to 50.000MHz
50.001 to 75.000MHz
75.001 to 100.000MHz
100.001 to 125.000MHz
Current, Output Disabled
Frequency
Nominal Frequency
3,8
Stability
4
,
(Ordering
Option)
Outputs
Output Logic Levels
2,3
Output Logic High
Output Logic Low
Output Logic High Drive
Output Logic Low Drive
Output Logic High Drive
5
Output Logic Low Drive
5
Load
Output Rise /Fall Time
2
32.768kHz to 345.6kHz
345.6kHz to 20.000MHz
20.001 to 50.000MHz
50.001 to 75.000MHz
75.001 to 125.000MHz
Output Leakage, Output Disabled
Duty Cycle
2,6
Period Jitter
7
RMS
Peak-Peak
RMS Jitter, 12kHz-20MHz
Output Enable/Disable
8
Output Enable
Output Disable
Disable time
Enable Internal Pull-Up Resistor
Start-Up Time
Operating Temp, (Ordering Option)
1]
2]
3]
4]
5]
6]
7]
8]
Symbol
V
DD
I
DD
Min
Supply
2.25
-0.5
Typical
2.5
Maximum
2.75
5
5
7
15
20
25
30
30
Units
V
V
mA
mA
mA
mA
mA
mA
uA
MHz
ppm
f
N
1
125.000
±20, ±25, ±32, ±50, ±100
V
OH
V
OL
I
OH
I
OL
I
OH
I
OL
I
OUT
t
R
/t
F
0.9*V
DD
0.1*V
DD
4
4
8
8
15
200
6
5
3
2
V
V
mA
mA
mA
mA
pF
ns
ns
ns
ns
ns
uA
%
ps
ps
I
Z
45
фJ
3.0
21
фJ
Enable/Disable
V
IH
V
IL
t
D
100
t
SU
T
OP
1.75
0.5
50
±10
55
1
ps
0.5
V
V
ns
Kohm
8
-10/70, -20/70, -40/85, -55/125
ms
°C
The power supply should have by-pass capacitors as close to the supply and to ground as possible, for example 0.1 and 0.01uF.
Parameters are tested a test circuit shown in Figure 1.
See Standard Frequencies and Ordering Information tables for more speci c information.
Includes initial accuracy, operating temperature, supply voltage, shock and vibration (not under operation) and aging for 50 and 100ppm options.
Duty Cycle is measured as On Time/Period, see Fig 2.
Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples, see Application Note for Typical Phase Noise and Jitter Performance.
The Output is Enabled if the Enable/Disable is left open.
Continuous frequency range is 1-125 MHz. 32.768 kHz is also available.
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Page4
Performance Speci
Table 4. Electrical Performance, 1.8V Option
Parameter
Voltage
1
Maximum Voltage
Current
2
≤20.000MHz
20.001 to 70.000MHz
70.001 to 100.000MHz
100.001 to 125.000MHz
Current, Output Disabled
Frequency
Nominal Frequency
3
Stability
4
, (Ordering Option)
Outputs
Output Logic Levels
2,3
Output Logic High
Output Logic Low
Output Logic High Drive
Output Logic Low Drive
Output Logic High Drive
5
Output Logic Low Drive
5
Load
Output Rise /Fall Time
2
<20.000MHz
20.000 to 50.000MHz
50.001 to 125.000MHz
Output Leakage, Output Disabled
Duty Cycle
2,6
Period Jitter
7
RMS
Peak-Peak
RMS Jitter, 12kHz-20MHz
Output Enable/Disable
8
Output Enable
Output Disable
Disable time
Enable Internal Pull-Up Resistor
Start-Up Time
Operating Temp, Ordering Option
1]
2]
3]
4]
5]
6]
7]
cations
Typical
1.8
Symbol
V
DD
I
DD
Min
Supply
1.71
-0.5
Maximum
1.89
3.6
5
15
20
25
30
Units
V
V
mA
mA
mA
mA
uA
MHz
ppm
f
N
1.544
125.000
±20, ±25, ±32, ±50, ±100
V
OH
V
OL
I
OH
I
OL
I
OH
I
OL
I
OUT
t
R
/t
F
0.9*V
DD
0.1*V
DD
2.8
2.8
8
8
15
6
5
3
V
V
mA
mA
mA
mA
pF
ns
ns
ns
uA
%
ps
ps
I
Z
45
фJ
3.0
21
фJ
Enable/Disable
V
IH
V
IL
t
D
1
t
SU
T
OP
1.26
0.5
50
±10
55
1
ps
0.5
100
8
-10/70, -20/70, -40/85, -55/125
V
V
ns
Mohm
ms
°C
The power supply should have by-pass capacitors as close to the supply and to ground as possible, for example 0.1 and 0.01uF.
Parameters are tested a test circuit shown in Figure 1.
See Standard Frequencies and Ordering Information tables for more speci c information.
Includes initial accuracy, operating temperature, supply voltage, shock and vibration (not under operation) and aging for 50 and 100ppm options.
Duty Cycle is measured as On Time/Period, see Fig 2.
Broadband Period Jitter measured using Wavecrest SIA3300C, 90K samples, see Application Note for Typical Phase Noise and Jitter Performance.
The Output is Enabled if the Enable/Disable is left open.
Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com
Page5
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
