MH25FAD-RFREQ2 datasheet, PDF - EEWORLD Datasheet

MH25FAD-RFREQ2: DescriptionCMOS/TTL Output Clock Oscillator, 50.001MHz Min, 60MHz Max, HALF SIZE, NICKEL HEADER, DIP-4; CategoryPassive components oscillator; File Size100KB，1 Pages; ManufacturerMtronPTI; Websitehttp://www.mtronpti.com; Environmental Compliance

Download Datasheet Parametric View All

MH25FAD-RFREQ2 Overview

CMOS/TTL Output Clock Oscillator, 50.001MHz Min, 60MHz Max, HALF SIZE, NICKEL HEADER, DIP-4

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	MtronPTI
Reach Compliance Code	unknown
maximum descent time	10 ns
Frequency Adjustment - Mechanical	NO
frequency stability	35%
JESD-609 code	e1
Manufacturer's serial number	MH
Installation features	THROUGH HOLE MOUNT
Maximum operating frequency	60 MHz
Minimum operating frequency	50.001 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CMOS/TTL
Output load	10 TTL, 50 PF
physical size	13.21mm x 13.21mm x 5.97mm
longest rise time	10 ns
Nominal supply voltage	5 V
surface mount	NO
maximum symmetry	40/60 %
Terminal surface	Tin/Silver/Copper (Sn/Ag/Cu)

MH Series Half-Size HCMOS/TTL

Compatible Oscillators

Half-Size HCMOS/TTL Compatible Oscillators

Available Stabilities vs. Temperature

See page 135 for gull wing configuration.

Available Symmetry

A = Available

N = Not Available

S = Standard

C = Consult Factory

Electrical Specifications

Pin Connections

Tri-state Control Logic

Pin 1 high or floating: clock signal output

Pin 1 low: output disables to high impedance

TTL load - See load circuit diagram #1 on page 137. HCMOS load - See load circuit diagram #2 on page 137.

Symmetry is measured at 1.4 V with TTL load, and at 50% Vdd with HCMOS load.

Rise/Fall times are measured between 0.5 V and 2.4 V with TTL load, and between 10% Vdd and 90% Vdd with HCMOS load.

See page 136 for suggested soldering conditions.

Analysis of the design steps of RS-485 bus interface circuit: [size=5] There are two ways to match the bus. One is to add matching resistors. A 120Ω matching resistor should be connected between the differential ports VA and VB at both ends of the bus to reduce ...; fish001 RF/Wirelessly

[NXP Rapid IoT Review] + NXP Rapid IoT Online IDE Air Quality Test: [i=s] This post was last edited by Feiyangzi at 2019-1-3 13:48 [/i] Following [url=https://en.eeworld.com/bbs/thread-1065909-1-1.html]https://en.eeworld.com/bbs/thread-1065909-1-1.html[/url], we will ...; 飞扬自我 RF/Wirelessly

How to remotely control a two-wheeled balancing vehicle via the Internet?: Want to remotely control the forward, backward, and turning of the electric two-wheeled balance vehicle through broadband or 4G network? How to achieve this, please give me some advice!! My thoughts a...; wxq13217952731 DIY/Open Source Hardware

How to get the most out of your low noise amplifier solution?: As 5G wireless networks continue to evolve, the performance of the radio front end plays an increasingly critical role in the RF receiver signal path, especially for low noise amplifiers (LNAs). With ...; 灞波儿奔 Analogue and Mixed Signal

Android4.4.2 source code compilation-iMX6Q/D core board-non-device tree source code: 5.3.1 Android source code overall compilation - based on Xunwei-IMX6 development board seriesThis section introduces how to compile Android source code as a whole, that is, compile uboot, kernel, and ...; 马佳徐徐 Embedded System

PYPL Programming Language Popularity Index, September 2022: September 2022 compared to a year ago...; dcexpert DIY/Open Source Hardware

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components