RC0805 (Pb Free)
5%, 1%
GENERAL PURPOSE CHIP RESISTORS
DATA SHEET
Product specification – Sep 03, 2004 V.2
Supersedes Date of Mar. 06, 2003
Product specification
2
10
Chip Resistor Surface Mount
RC
SERIES
0805 (Pb Free)
SCOPE
This specification describes RC0805 series chip resistors with lead-free terminations made by thick film process.
ORDERING INFORMATION
Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and
resistance value.
PHYCOMP ORDERING CODE
12NC
(1)
CODE
CTC
XXX XXXXX L
(2)
(3)
(4)
CODE
2322 / 2350
RC0805
PAPER / PE TAPE ON REEL (units)
(2)
5,000
730 61xxx
734 6xxxx
521 10xxx
730 91002
10,000/not preferred
730 71xxx
734 7xxxx
-
730 91003
20,000
730 81xxx
734 8xxxx
-
730 92002
X X X XX XXXX L
(1) (2) (3)
(4)
(5)
(6)
TYPE/ START
0805 IN
(1)
RC11
RC12
2322
2322
TOL. RESISTANCE
(%) RANGE
±5%
±1%
±5%
-
1 to 10 MΩ
1 to 10 MΩ
11 to 22 MΩ
0
Ω
(1) TOLERANCE
F = ±1%
J = ±5%
(2) PACKAGING TYPE
R = Paper/PE taping reel
HRC11
2350
Jumper
2322
(1) The resistors have a 12-digit
ordering code starting with
2322/2350.
(2) The subsequent 4 or 5 digits
indicate the resistor
tolerance and packaging.
(3) The remaining 4 or 3 digits
represent the resistance value
with the last digit indicating
the multiplier as shown in the
table of “Last digit of 12NC”.
(4) “L” means lead-free
terminations.
O
RDERING EXAMPLE
The ordering code of a RC12
resistor, value 56
X
with ±1%
tolerance, supplied in tape of
5,000 units per reel is:
232273465609L.
NOTE
Last digit of 12NC
Resistance decade
0.01 to 0.0976
X
0.1 to 0.976
X
1 to 9.76
X
10 to 97.6
X
100 to 976
X
1 to 9.76 k
X
10 to 97.6 k
X
100 to 976 k
X
1 to 9.76 M
X
10 to 97.6 M
X
Example:
0.02
X
0.3
X
1
X
33 k
X
10 M
X
=
=
=
=
=
(3)
(3) TEMPERATURE COEFFICIENT
OF RESISTANCE
– = Base on spec
Last digit
0
7
8
9
1
2
3
4
5
6
0200 or 200
3007 or 307
1008 or 108
3303 or 333
1006 or 106
(4) TAPING REEL
07 = 7 inch dia. Reel
10 = 10 inch dia. Reel (not preferred)
13 = 13 inch dia. Reel
(5) RESISTANCE VALUE
5R6, 56R, 560R, 5K6, 56K, 22M
(6) RESISTOR TERMINATIONS
L = Lead free terminations (pure Tin)
O
RDERING EXAMPLE
The ordering code of a RC0805
chip resistor, value 56
X
with
±1% tolerance, supplied in 7-inch
tape reel is: RC0805FR-0756RL.
1. The “L” at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp
“LFP”= lead free production.
2. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet.
3. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006)
www.yageo.com
Sep 03, 2004 V.2
Product specification
3
10
Chip Resistor Surface Mount
RC
SERIES
0805 (Pb Free)
MARKING
RC0805
E-24 series: 3 digits
ynsc001
Fig. 1
Value=10 KΩ
First two digits for significant figure and 3rd digit for number of zeros
Both E-24 and E-96 series: 4 digits
ynsc004
Fig. 2
Value=10 KΩ
First three digits for significant figure and 4th digit for number of zeros
For marking codes, please see EIA-marking code rules in data sheet “Chip resistors instruction”.
CONSTRUCTION
The resistors are constructed out of
a high-grade ceramic body. Internal
handbook, 4 columns
metal electrodes are added at each
end and connected by a resistive
H
paste. The composition of the paste
is adjusted to give the approximate
I2
required resistance and laser cutting
of this resistive layer that achieves
Fig. 3
Chip resistor construction
tolerance trims the value. The
resistive layer is covered with a
protective coat and printed with the
resistance value. Finally, the two external terminations (pure Tin) are added. See fig. 3.
DIMENSIONS
Table 1
TYPE
L (mm)
W (mm)
H (mm)
I
1
(mm)
I
2
(mm)
RC0805
2.00 ±0.10
1.25 ±0.10
0.50 ±0.10
0.35 ±0.20
0.35 ±0.20
L
MBE940_a
protective coat
resistor layer
inner electrode
end termination
ceramic substrate
MBE940_a
protective coat
I
1
W
Fig. 4
Chip resistor dimension
For dimension see Table 1
www.yageo.com
Sep 03, 2004 V.2
Product specification
4
10
Chip Resistor Surface Mount
RC
SERIES
0805 (Pb Free)
ELECTRICAL CHARACTERISTICS
Table 2
CHARACTERISTICS
Operating Temperature Range
Maximum Working Voltage
Maximum Overload Voltage
Dielectric Withstanding Voltage
Resistance Range
RC0805 1/8 W
–55 °C to +155 °C
150 V
300 V
300 V
5% (E24) 1
Ω
to 22 MΩ
1% (E96) 1
Ω
to 10 MΩ
Zero Ohm Jumper < 0.05
Ω
10
Ω
< R
≤
10 MΩ
R
≤
10
Ω;
R > 10 MΩ
Rated Current
Maximum Current
±100 ppm/°C
±200 ppm/°C
2.0 A
5.0 A
FOOTPRINT AND SOLDERING
PROFILES
For recommended footprint and
soldering profiles, please see the
special data sheet “Chip resistors
mounting”.
ENVIRONMENTAL DATA
For material declaration
information (IMDS-data) of the
products, please see the
separated info “Environmental
data”.
Temperature Coefficient
Jumper Criteria
PACKING STYLE AND PACKAGING QUANTITY
Table 3
Packing style and packaging quantity
PRODUCT TYPE
RC0805
PACKING STYLE
Paper / PE Taping Reel (R)
REEL DIMENSION
7" (178 mm)
10" (254 mm) / not preferred
13" (330 mm)
QUANTITY PER REEL
5,000 units
10,000 units
20,000 units
NOTE
1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet “Packing” document.
www.yageo.com
Sep 03, 2004 V.2
Product specification
5
10
Chip Resistor Surface Mount
RC
SERIES
0805 (Pb Free)
FUNCTIONAL DESCRIPTION
POWER RATING
RC0805 rated power at 70°C is 1/8 W
R
ATED VOLTAGE
The DC or AC (rms) continuous working voltage
corresponding to the rated power is determined by
the following formula:
V=√(P X R)
Where
V=Continuous rated DC or
AC (rms) working voltage (V)
P=Rated power (W)
R=Resistance value (X)
PULSE LOADING CAPABILITIES
Pmax
(%Prated)
100
MRA632
50
0
−55
0
50 70
155
100
Tamb (°C)
Fig. 5
Maximum dissipation (P
max
) in percentage of rated power
as a function of the operating ambient temperature (T
amb
)
10
4
MBD587
Vmax
(V)
1.2/50
µs
10
3
10/700
µs
10
2
10
10
10
2
10
3
10
4
10
5
10
6
R n (Ω)
10
7
Fig. 6
Maximum permissible peak pulse voltage without failing to open circuit’ in accordance with DIN IEC 60040 (CO) 533 for type:
RC0805
www.yageo.com
Sep 03, 2004 V.2
Sensor
京公网安备 11010802033920号
EEWORLD
