EEWORLDEEWORLDEEWORLD

Part Number

Search

SE-K100M33BZFV811

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 100V, 20% +Tol, 20% -Tol, 33uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size60KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

SE-K100M33BZFV811 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 100V, 20% +Tol, 20% -Tol, 33uF, Through Hole Mount, ROHS COMPLIANT

SE-K100M33BZFV811 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance33 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.076 mA
Manufacturer's serial numberSE-K
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)100 V
ripple current95 mA
surface mountNO
Delta tangent0.1
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SE-K
[ For General ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors Rated Voltage up to 450V
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C / -25° ~ +105°C
Working Voltage : 6.3 ~ 250V / 350 ~ 450V
Rate Capacitance Range : 0.47 ~ 15000µF / 0.47 ~ 150µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01CV + 3 / 0.03CV + 10
( After 2 Minutes Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
W V (V) : 6.3
10
16
25
35
50
63
80
100 160 ~ 250 350 ~ 450
D.F (%) : 26
22
18
16
14
12
10
10
10
15
20
For capacitor whose capacitance excceds 1000 µF. The value of DF(%) is increased by 2% for every
addition of 1000 µF.
Load Life : 1000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 500 Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DESCRIPTION
Lower-cost capacitors expressly intended for high
density printed circuit board.
Ideally suited for general-purpose applications,
entertainment electronics.
Feature High CV Product with Moderate Cost
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
6.3~100V 100~680µF
6.3~110V 1000~22000µF
160~450V ALL Cap(µF)
120
1.00
1.00
1.00
1.00
300
1.20
1.10
1.05
1.05
1K 10K~100K
1.30
1.45
1.15
1.25
1.10
1.15
1.10
1.50
Temperature(°C)
Factor
65
1.80
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
AM335X GPIO Register Operation
To feed the dog (gpio2_0) before start_kernel, gpio address: GPIO2: 0x481AC000,GPIO_OE:offset=134h,GPIO_DATAOUT=13Ch Add the following two lines of code in the decompress_kernel function in the ./arch...
别叫你哥许鲜森 ARM Technology
New mobile phone power management chip
A well-functioning power management circuit is the basis for the normal operation of a mobile phone. If the power management circuit can be power-saving, efficient, multifunctional and occupy a small ...
zbz0529 Power technology
Overview of IoT Communication Technologies
IoT communication technology is divided into wired and wireless, and different communication methods are used according to different application scenarios and needs. Wired communicationWired communica...
Jacktang RF/Wirelessly
ESD Request Assistance
[i=s]This post was last edited by bluefox0919 on 2019-1-2 17:30[/i] I have an old project on hand. The original designer has left the company for many years... I need to solve the ESD. The appearance ...
bluefox0919 PCB Design
How to compensate for the unbalanced output of a strain gauge bridge?
The strain gauge bridge has a zero output of 4mV, a full-scale output of about 4.5mV, and a full-scale output change of 0.5mV, but the zero offset is as high as 4mV;zero offset compensation solution:1...
ActiveAndy Analog electronics
MSP430G2553 State Machine Modeling
The program requires that if p1.3 is pressed short, p1.0 will be inverted, and if p1.3 is pressed long, p1.6 will be inverted. The following is the program: #include "msp430g2553.h" #define IDLE 0 #de...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号