SPECIFICATION SUMMARY
Capacitance Range
.001uF to 100uF
Capacitance Tolerance
Standard tolerance is ±10% : Tolerances of ±20%, ±5%, ±2%,
±1% are available.
Operating Temperature Range
From -55°C to +125°C without derating
Enclosure/ Construction
Hermetically Sealed in metal tubes with
glass-to-metalsolder-sealed terminals
Voltage Rating
DC working voltages of 50VDC, 75VDC,100VDC, 150VDC,
200VDC, 300 VDC and 400VDC are standard.
Quality Control
Capacitors are tested 100% for:
° Capacitance tolerance
° Dissipation Factor
° Dielectric withstanding voltage
° Insulation Resistance
° Equivalent Series Resistance (ESR)
Environmental
Parameter
Thermal Aging
Thermal Shock
Vibration
Immersion
Shock
Moisture Resist
Life
Paragraph
3.7
3.8
3.15
3.17
3.19
3.2
3.27
Reference MIL-C-83421
CHARACTERISTICS
Insulation Resistance
Temparature(°C)
25°C
Megaohms x
100,000
Microfarads
85°C
7,000
125°C
700
Capacitance Change
Temparature(°C)
-55°C
Percentage Change
±1.5
(typical)
+25°C
0
+85°C
±0.3
+125°C
±0.8
Insulation Resistance
Capacitance Change
Dissipation Factor
When measured at the frequency specified for capacitance
measurements, the dissipation factor shall not exceed 0.3% from
+25°C to +125°C.
Dielectric Strength
Capacitors shall withstand a DC potential of 200% rated
voltage for two minutes without damage. When the
capacitor section is insulated from the case, the
capacitors shall withstand a DC potential of 200% rated
voltage applied between the case and the
terminals.Test voltage must be applied and discharged
through a resistance of 1 OHM per volt, minimum and at
25°C.
DETAIL DATA
50VDC 75VDC 100VDC 150VDC 200VDC 300VDC 400VDC
PART Cap B C D E F H J
NUMBER
µF D L AWG D L AWG D L AWG D L AWG D L AWG D L AWG D L AWG
MC52_103K 0.010 0.174 0.531 24 0.174 0.625 24 0.174 0.625 24 0.174 0.625 24 0.193 0.688 24 0.235 0.688 22
MC52_123K 0.010 0.174 0.531 24 0.174 0.625 24 0.174 0.625 24 0.174 0.625 24 0.235 0.688 22 0.235 0.812 22
MC52_153K 0.015 0.174 0.531 24 0.174 0.625 24 0.174 0.625 24 0.174 0.625 24 0.235 0.688 22 0.235 0.812 22
MC52_183K 0.020 0.174 0.531 24 0.174 0.625 24 0.174 0.625 24 0.193 0.625 24 0.235 0.812 22 0.235 0.812 22
MC52_223K 0.022 0.174 0.531 24 0.174 0.625 24 0.174 0.625 24 0.193 0.625 24 0.235 0.812 22 0.312 0.688 22
MC52_273K 0.030 0.174 0.531 24 0.174 0.625 24 0.193 0.625 24 0.235 0.625 22 0.312 0.688 22 0.312 0.812 22
MC52_333K 0.033 0.174 0.531 24 0.174 0.625 24 0.193 0.688 24 0.235 0.625 22 0.312 0.688 22 0.312 0.812 22
MC52_393K 0.040 0.174 0.625 24 0.174 0.625 24 0.193 0.688 24 0.235 0.688 22 0.312 0.812 22 0.312 0.938 22
MC52_473K 0.047 0.174 0.531 24 0.174 0.625 24 0.193 0.625 24 0.235 0.625 22 0.235 0.688 22 0.312 0.812 22 0.400 0.812 20
MC52_563K 0.060 0.174 0.531 24 0.174 0.625 24 0.193 0.625 24 0.235 0.688 22 0.312 0.625 22 0.312 0.938 22 0.400 0.812 20
MC52_683K 0.068 0.174 0.625 24 0.174 0.625 24 0.235 0.625 22 0.235 0.688 22 0.312 0.625 22 0.312 0.938 22 0.400 0.938 20
MC52_823K 0.080 0.174 0.625 24 0.193 0.625 24 0.235 0.625 22 0.312 0.625 22 0.312 0.688 22 0.400 0.812 20 0.400 0.938 20
MC52_104K 0.10 0.174 0.625 24 0.193 0.625 24 0.235 0.688 22 0.312 0.688 22 0.312 0.688 22 0.400 0.938 20 0.400 1.125 20
MC52_124K 0.12 0.174 0.625 24 0.235 0.625 22 0.235 0.688 22 0.312 0.688 22 0.312 0.812 22 0.400 0.938 20 0.400 1.312 20
MC52_154K 0.15 0.193 0.625 24 0.235 0.625 22 0.312 0.625 22 0.312 0.812 22 0.312 0.812 22 0.400 1.125 20 0.400 1.312 20
MC52_184K 0.18 0.193 0.625 24 0.312 0.625 22 0.312 0.625 22 0.312 0.812 22 0.400 0.688 20 0.400 1.312 20 0.562 1.125 20
MC52_224K 0.22 0.235 0.625 22 0.312 0.625 22 0.312 0.688 22 0.312 0.812 22 0.400 0.812 20 0.400 1.312 20 0.562 1.125 20
MC52_274K 0.27 0.235 0.625 22 0.312 0.625 22 0.312 0.688 22 0.400 0.812 20 0.400 0.812 20 0.562 1.125 20 0.562 1.312 20
MC52_334K 0.33 0.312 0.625 22 0.312 0.625 22 0.312 0.812 22 0.400 0.812 20 0.400 0.938 20 0.562 1.125 20 0.562 1.562 20
MC52_394K 0.39 0.312 0.625 22 0.312 0.843 22 0.312 0.812 22 0.400 0.812 20 0.400 0.938 20 0.562 1.125 20 0.562 1.562 20
MC52_474K 0.47 0.312 0.625 22 0.312 0.843 22 0.400 0.688 20 0.400 0.938 20 0.400 1.125 20 0.562 1.562 20 0.562 1.812 20
MC52_564K 0.56 0.312 0.625 22 0.312 0.843 22 0.400 0.812 20 0.400 1.125 20 0.400 1.312 20 0.562 1.562 20 0.670 1.562 20
MC52_684K 0.68 0.312 0.843 22 0.312 0.843 22 0.400 0.812 20 0.400 1.125 20 0.500 1.125 20 0.670 1.312 20 0.670 1.812 20
MC52_824K 0.82 0.312 0.843 22 0.400 0.843 20 0.400 0.938 20 0.500 0.938 20 0.500 1.125 20 0.670 1.562 20 0.750 1.812 20
MC52_105K 1.0 0.312 0.843 22 0.400 0.843 20 0.400 0.938 20 0.500 1.125 20 0.562 1.125 20 0.670 1.812 20 0.750 2.062 20
MC52_125K 1.2 0.400 0.843 20 0.400 1.125 20 0.500 0.938 20 0.500 1.125 20 0.562 1.312 20 0.670 1.812 20 1.000 1.812 20
MC52_155K 1.5 0.400 0.843 20 0.400 1.125 20 0.500 0.938 20 0.500 1.312 20 0.562 1.312 20 0.750 2.062 20 1.000 1.812 20
MC52_185K 1.8 0.400 0.843 20 0.400 1.125 20 0.500 1.125 20 0.562 1.312 20 0.562 1.812 20 0.750 2.062 20 1.000 2.062 20
MC52_205K 2.0 0.400 0.843 20 0.500 1.125 20 0.500 1.125 20 0.562 1.312 20 0.562 1.812 20 0.750 2.062 20 1.000 2.062 20
MC52_225K 2.2 0.400 1.125 20 0.500 1.125 20 0.500 1.125 20 0.562 1.562 20 0.562 1.812 20 1.000 1.812 20 1.000 2.312 20
MC52_275K 2.7 0.400 1.125 20 0.500 1.125 20 0.562 1.312 20 0.562 1.812 20 0.670 1.562 20 1.000 1.812 20 1.000 2.562 20
MC52_305K 3.0 0.400 1.125 20 0.500 1.125 20 0.562 1.312 20 0.562 1.812 20 0.750 1.562 20 1.000 2.062 20 1.000 2.687 18
MC52_335K 3.3 0.400 1.125 20 0.562 1.125 20 0.562 1.312 20 0.562 1.812 20 0.750 1.812 20 1.000 2.312 20
MC52_395K 3.9 0.500 1.125 20 0.562 1.125 20 0.562 1.562 20 0.670 1.812 20 0.750 1.812 20 1.000 2.562 20
MC52_475K 4.7 0.500 1.125 20 0.562 1.312 20 0.670 1.312 20 0.670 1.812 20 0.750 2.062 20
MC52_505K 5.0 0.500 1.125 20 0.562 1.312 20 0.670 1.312 20 0.750 1.562 20 0.750 2.062 20
MC52_565K 5.6 0.500 1.125 20 0.670 1.312 20 0.670 1.312 20 0.750 1.812 20 0.750 2.312 20
MC52_685K 6.8 0.562 1.125 20 0.670 1.312 20 0.670 1.562 20 0.750 2.063 20 1.000 1.812 20
MC52_825K 8.2 0.562 1.321 20 0.670 1.625 20 0.670 1.812 20 0.750 2.375 20 1.000 2.062 20
MC52_106K 10 0.670 1.321 20 0.670 1.625 20 0.750 1.812 20 0.750 2.625 20 1.000 2.312 20
MC52_126K 12 0.670 1.321 20 0.670 1.875 20 0.750 1.812 20 1.000 1.875 20 1.000 2.563 18
MC52_156K 15 0.750 1.375 20 0.750 1.875 20 1.000 1.875 20 1.000 2.125 20 1.125 2.687 18
MC52_186K 18 0.750 1.375 20 0.750 2.125 20 1.000 1.875 20 1.000 2.625 18 1.250 2.687 18
MC52_206K 20 0.750 1.625 20 0.750 2.625 20 1.000 1.875 20 1.000 2.875 18 1.250 2.687 18
MC52_226K 22 0.750 1.625 20 0.750 2.625 20 1.000 1.875 20 1.125 2.937 18 1.250 2.937 18
MC52_256K 25 1.000 1.375 20 1.000 1.875 20 1.000 2.125 20 1.250 2.687 18 1.390 2.937 18
MC52_276K 27 1.000 1.375 20 1.000 1.875 20 1.000 2.125 20 1.250 2.687 18 1.390 2.937 18
MC52_306K 30 1.000 1.375 20 1.000 2.125 20 1.000 2.375 20 1.250 2.937 18 1.390 3.187 18
MC52_336K 33 1.000 1.375 20 1.000 2.125 20 1.000 2.625 18 1.250 2.937 18 1.390 3.187 18
MC52_396K 39 1.000 1.625 20 1.000 2.625 18 1.000 2.875 18 1.390 2.937 18 1.500 3.187 18
MC52_476K 47 1.000 1.875 20 1.000 2.875 18 1.125 2.937 18 1.500 2.937 18
MC52_506K 50 1.000 1.875 20 1.125 2.937 18 1.250 2.937 18 1.500 3.187 18
MC52_566K 56 1.000 1.875 20 1.125 2.937 18 1.250 2.937 18 1.500 3.187 18
MC52_686K 68 1.000 2.125 20 1.250 2.937 18 1.390 2.937 18
MC52_756K 75 1.000 2.375 20 1.250 2.937 18 1.390 2.937 18
MC52_826K 82 1.000 2.625 18 1.250 3.187 18 1.390 3.187 18
MC52_906K 90 1.000 2.875 18 1.390 2.937 18 1.390 3.187 18
MC52_107K 100 1.000 3.187 18 1.390 3.187 18 1.500 3.187 18
Other Information
HOW TO ORDER
TYPE
Metallized Polycarbonate
MC
52B
104
K
STYLE / TERMINALS / VOLTAGE
CAPACITANCE IN PICOFARADS
The first two digits are significant, the third represents the number of zeros (e.g.
104 = 100,000 pfd = .1mfd)
TOLERANCE
Standard tolerance is ±10% : Tolerances of ±20%, ±5%, ±2%, ±1% are available.
Marking And DateCode
All capacitors are marked with company initials "EC", or EC trademark , type (MC), capacitance, tolerance, rated DC working voltage
and date code. The first two digits of the date code represent the year, the second two digits the week, i.e., 9952 is the 52nd week of
1999, 0102 is the second week of 2001.
Quality Assurance
In the construction of the components described, the full intent of the specification will be met. Electronic Concepts, Inc., however,
reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit
improvements in the design of its products. Components made under military approvals will be in accordance with the approval
requirements.
SALES OFFICES
United States
Eastern:
New Jersey 732-542-7880
Central:
Illinois 630-668-8747
email: sales@ecicaps.com
website:www.ecicaps.com
P/N 161011130 Rev.
Europe
Ireland
Electronic Concepts LTD
IDA Estate, Oughterad
Co. Galway, Ireland
tel: +353-91-552385,552432
fax: +353-91-552387
email: sales@ecicaps.ie
website:www.electronicconcepts.ie