Features ....................................................................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
LVPECL and FlexSwing Termination .................................................................................................................................. 17
LVDS, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 18
HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 18
Low-power HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V.................... 18
Dimensions and Patterns ― 2.0 x 1.6 mm x mm ....................................................................................................................... 19
Dimensions and Patterns ― 2.5 x 2.0 mm x mm ....................................................................................................................... 20
Dimensions and Patterns ― 3.2 x 2.0 mm x mm ....................................................................................................................... 21
Revision History ......................................................................................................................................................................... 22
Rev 0.52
Page 3 of 23
www.sitime.com
SiT9375
Low Jitter Differential XO for Standard Frequencies
Electrical Characteristics
ADVANCED
All Min and Max limits in the Electrical Characteristics tables are specified over operating temperature and rated operating
voltage with standard output termination shown in the termination diagrams. Typical values are at 25°C and nominal
supply voltage.
Table 3. Electrical Characteristics – Common to All Output Signaling Types
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
–
Min.
Typ.
Max.
Unit
MHz
ppm
Condition
Refer to frequencies listed in
Ordering Information
section.
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and 10 years
aging at 25°C
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and first year aging
at 25°C
Ambient temperature of 25°C
Extended commercial, ambient temperature
Industrial, ambient temperature
Ambient temperature
Extended industrial, ambient temperature
Voltage-supply order code “YY”
Voltage-supply order code “XX”
Voltage-supply order code “18”.
Contact SiTime
for 1.5 V
Voltage-supply order code “25”
Voltage-supply order code “33”
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
See
Figure 5
and
Figure 7
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin toggles to enable logic level to
the time clock pins reach 90% of swing. See
Figure 12
Measured from the time OE pin toggles to disable logic level to
the last clock edge. See
Figure 13
12 kHz to 20 MHz offset frequency integration bandwidth,
156.25 MHz
12 kHz to 20 MHz offset frequency range, 156.25 MHz
12 kHz to 20 MHz offset frequency range, 155.52 MHz
156.25 MHz
156.25 MHz
Frequency Range
Standard frequencies
–
±20
Frequency Stability
–
–
–
10 Year Aging
Operating Temperature Range
F_10y
T_use
–
-20
-40
-40
-40
Supply Voltage
Vdd
1.71
2.25
1.71
2.25
2.97
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Startup Time
Output Enable Time
Output Disable Time
VIH
VIL
Z_in
DC
T_start
T_oe
T_od
70%
–
–
45
–
–
–
–
–
–
±1
–
–
–
–
–
–
1.80
2.50
3.30
–
–
100
–
1
–
–
±25
±30
±50
–
+70
+85
+95
+105
ppm
ppm
ppm
ppm
°C
°C
°C
°C
V
V
V
V
V
Temperature Range
Supply Voltage
3.63
3.63
1.89
2.75
3.63
Input Characteristics
–
Vdd
30%
–
55
5
100+3 clock
cycles
100+3 clock
cycles
Vdd
kΩ
%
ms
ns
ns
Output Characteristics
Startup, OE and SE Timing
Jitter and Phase Noise
RMS Phase Jitter (random)
Spurious Phase Noise
RMS Period
Jitter
[1]
Jitter
[1]
T_phj
PN_spur_a
PN_spur_b
T_jitt_per
T_jitt_cc
Peak Cycle-to-cycle
–
–
–
–
–
200
-110
-80
1
6
–
–
–
–
–
fs
dBc
dBc
ps
ps
Note:
1. Measured according to JESD65B.
Rev 0.52
Page 4 of 23
www.sitime.com
SiT9375
Low Jitter Differential XO for Standard Frequencies
ADVANCED
Table 4. Electrical Characteristics – LVPECL
|
Supply voltages: 2.5 V
±10%,
3.3 V
±10%,
2.25 V to 3.63 V
Parameter
Current Consumption, Output
Enabled without Termination
Current Consumption, Output
Enabled with Termination 1
Current Consumption, Output
Enabled with Termination 2
Current Consumption, Output
Disabled without Termination
Current Consumption Output
Disabled with Termination 1
Current Consumption, Output
Disabled with Termination 2
OE Leakage Current
Symbol
Idd_oe_nt
Idd_oe_wt1
Idd_oe_wt2
Idd_od_nt
Idd_od_wt1
Idd_od_wt2
I_leak
Min.
–
–
–
–
–
–
–
Typ.
43
52
71
58
58
86
37
Max.
–
–
–
–
–
–
–
Unit
mA
mA
mA
mA
mA
mA
mA
Condition
Excluding load termination current
Including load termination current. See
Figure 15
for
termination
Including load termination current. See
Figure 18
for
termination
Excluding load termination current
Including load termination current. See
Figure 15
for
termination
Including load termination current. See
Figure 18
for
termination
OE = disable logic, DC termination, OUTP and OUTN held
The following circuit, such as the circuit 2843 in the red circle, is there any other purpose? The 1st pin of the chip is directly connected to 817.The question is, can the RC network connected to pin...
03 The foundation of development, the platform emerges
I often use IAR as my development environment. I checked the Nations.N32G430_Library.1.0.0 in the documentation and found that only IAR projects ...
[i=s]This post was last edited by alan000345 on 2019-4-9 07:44[/i] [p=30, null, left]Bluetooth has always been a standard feature of smart devices, whether it is a smartphone, a laptop, or a tablet. W...
Complete introduction of 12V power supply with voltage meter, terminal and emergency stop button :https://www.hackster.io/DerPandaHammer/power-in-a-box-f16849...
Use STC8G1K08 I2C bus to control RDA5807M to achieve high-fidelity reception of FM signals. The frequency is displayed by a 0.36- inch common-anode LED digital tube. The 8G1K08 will not interfere with...
Samsung's unprecedented success is in 2020, but Yoon Jong-yong believes there must be a crisis here . By Peter Lewis Samsung Electronics' VIP building is located in the Samsung Industrial Park in Suwo...
A weighing sensor is a force measuring instrument that can convert the force signal of the measured object into a measurable electrical signal output. It is used in industries such as industry, electr...[Details]
Among lithium-ion battery protection IC products, only 4 cells are currently connected in series. Therefore, when designing lithium-ion battery protection circuits with more than 4 cells, many engi...[Details]
With the development of digital and network technology, the concept of "cloud" appears more and more around us. As the demand for multi-level cross-regional large-scale networking and massive dat...[Details]
Since the beginning of this year, many related companies such as Shuangyuan and Ankai Micro have successfully listed, and Sikan Technology, Xinxinteng, Changbudao, and Hikvision are rushing for IPO...[Details]
Global battery giant Panasonic has begun to clearly slow down its production capacity expansion. According to Nikkei.com, on December 20, Panasonic Energy said that after "careful consideration" it...[Details]
Square wave and triangle wave generator
Connect the square wave and triangle wave generator according to the circuit and parameters shown in Figure 11-2. Figure 11-2 (2) Adjust the potentiometer Rp...[Details]
Note: The kernel version number is 3.10.101 1. Implementation of atomic operations in ARM architecture In Atomic Operations (I), we have mentioned that various architectures are organized into ...[Details]
Capacitors are essential components for various electronic product terminals and play a vital role in electronic systems. With the improvement of electronic product manufacturing level and increasi...[Details]
Analog chip giant Texas Instruments mainly sells small analog chips. Each chip costs only a few cents or dollars, and is an indispensable component in electronic products. Because analog chips are ne...[Details]
How to measure current with a digital multimeter 1. Disconnect the circuit; 2. Insert the black test lead into the com port and the red test lead into the mA or 20A port; 3. Turn the function...[Details]
It is understood that Foxconn's iPhone production line in India was officially put into use in August. However, because the preferential export tariffs that Apple hopes to reach with the Indian gover...[Details]
introduction Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detection is...[Details]
Jiwei.com reported on December 14 that Huawei Terminal’s official Weibo account announced today that it will release the new nova 8 series online on December 23. The slogan of Huawei's nova8 series...[Details]
CCTV's National Defense Military Channel "National Defense Science and Industry" once reported the story of Li Shifeng, a sheet metal worker at Xi'an Aircraft Corporation, who knocked out hundreds ...[Details]
In order to achieve synchronization between threads, a mutex lock is usually added before executing the critical code segment, and unlocked after the critical code segment is executed. In order to ...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
