FINAL
Am27X512
512 Kilobit (64 K x 8-Bit) CMOS ExpressROM Device
DISTINCTIVE CHARACTERISTICS
s
As an OTP EPROM alternative:
— Factory optimized programming
— Fully tested and guaranteed
s
As a Mask ROM alternative:
— Shorter leadtime
— Lower volume per code
s
Fast access time
— 70 ns
s
Single +5 V power supply
s
Compatible with JEDEC-approved EPROM
pinout
s
±10%
power supply tolerance
s
High noise immunity
s
Low power dissipation
— 100 µA maximum CMOS standby current
s
Available in Plastic Dual-In-line Package (PDIP)
and Plastic Leaded Chip Carrier (PLCC)
s
Latch-up protected to 100 mA from –1 V to
V
CC
+ 1 V
s
Versatile features for simple interfacing
— Both CMOS and TTL input/output compatibility
— Two line control functions
GENERAL DESCRIPTION
The Am27X512 is a factory programmed and tested
OTP EPROM. It is programmed after packaging prior to
final test. Every device is rigorously tested under AC
and DC operating conditions to your stable code. It is
organized as 64 Kwords by 8 bits per word and is avail-
able in plastic dual in-line packages (PDIP), as well as
plastic leaded chip carrier (PLCC) packages. Express-
ROM devices provide a board-ready memory solution
for medium to high volume codes with short leadtimes.
This offers manufacturers a cost-effective and flexible
alternative to OTP EPROMs and mask programmed
ROMs.
Data can be accessed as fast as 70 ns, allowing
high-performance microprocessors to operate with re-
duced WAIT states. The device offers separate Output
Enable (OE#) and Chip Enable (CE#) controls, thus
eliminating bus contention in a multiple bus micropro-
cessor system.
AMD’s CMOS process technology provides high
speed, low power, and high noise immunity. Typical
power consumption is only 80 mW in active mode, and
100 µW in standby mode.
BLOCK DIAGRAM
V
CC
V
SS
OE#
CE#
Output Enable
Chip Enable
and
Prog Logic
Y
Decoder
A0–A15
Address
Inputs
Output
Buffers
Data Outputs DQ0–DQ7
Y
Gating
X
Decoder
524,288
Bit Cell
Matrix
12081F-1
Publication#
12081
Rev:
F
Amendment/0
Issue Date:
May 1998
PRODUCT SELECTOR GUIDE
Family Part Number
Speed Options
Max Access Time (ns)
CE# (E#) Access (ns)
OE# (G#) Access (ns)
V
CC
= 5.0 V
±
5%
V
CC
= 5.0 V
±
10%
-70
70
70
70
-90
90
90
40
-120
120
120
50
-150
150
150
65
-200
200
200
75
250
250
100
Am27X512
-255
CONNECTION DIAGRAMS
Top View
DIP
A7
A12
A15
PLCC
V
CC
A14
A13
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
V
SS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
CC
A14
A13
A8
A9
A11
OE# (G#)/V
PP
A10
CE# (E#)
DQ7
DQ6
DQ5
DQ4
DQ3
12081F-2
4 3 2 1 32 31 30
A6
A5
A4
A3
A2
A1
A0
NC
DQ0
5
6
7
8
9
10
11
12
13
14 15 16 17 18 19 20
V
SS
DU
DQ3
DQ1
DQ2
DQ4
DQ5
29
28
27
26
25
24
23
22
21
A8
A9
A11
NC
OE# (G#)/V
PP
A10
CE# (E#)
DQ7
DQ6
DU
12081F-3
Notes:
1. JEDEC nomenclature is in parenthesis.
2. Don’t use (DU) for PLCC.
PIN DESIGNATIONS
A0–A15
CE# (E#)
DQ0–DQ7
OE# (G#)
PGM# (P#)
V
CC
V
PP
V
SS
NC
= Address Inputs
= Chip Enable Input
= Data Input/Outputs
= Output Enable Input
= Program Enable Input
LOGIC SYMBOL
16
A0–A15
DQ0–DQ7
CE# (E#)
8
= V
CC
Supply Voltage
= Program Voltage Input
= Ground
= No Internal Connection
12081F-4
OE# (G#)
2
Am27X512
ORDERING INFORMATION
Standard Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed
by a combination of the following:
AM27X512
-70
J
C
XXXXX
CODE DESIGNATION
Assigned by AMD
TEMPERATURE RANGE
C = Commercial (0°C to +70
°
C)
I = Industrial (–40
°
C to +85
°
C)
PACKAGE TYPE
P = 28-Pin Plastic Dual In-Line Package (PD 028)
J = 32-Pin Plastic Leaded Chip Carrier (PL 032)
SPEED OPTION
See Product Selector Guide and Valid Combinations
DEVICE NUMBER/DESCRIPTION
Am27X512
512 Kilobit (64 K x 8-Bit) CMOS ExpressROM Device
Valid Combinations
AM27X512-70
AM27X512-90
AM27X512-120
AM27X512-150
AM27X512-200
AM27X512-255
V
CC
= 5.0 V
±
5%
PC, JC, PI, JI
Valid Combinations
Valid Combinations list configurations planned to be sup-
ported in volume for this device. Consult the local AMD sales
office to confirm availability of specific valid combinations and
to check on newly released combinations.
Am27X512
3
FUNCTIONAL DESCRIPTION
Read Mode
To obtain data at the device outputs, Chip Enable (CE#)
and Output Enable (OE#) must be driven low. CE# con-
trols the power to the device and is typically used to se-
lect the device. OE# enables the device to output data,
independent of device selection. Addresses must be
stable for at least t
ACC
–t
OE
. Refer to the Switching
Waveforms section for the timing diagram.
CE# should be decoded and used as the primary de-
vice-selecting function, while OE#/V
PP
be made a com-
mon connection to all devices in the array and
connected to the READ line from the system control
bus. This assures that all deselected memory devices
are in their low-power standby mode and that the out-
put pins are only active when data is desired from a
particular memory device.
Standby Mode
The device enters the CMOS standby mode when CE#
is at V
CC
±
0.3 V. Maximum V
CC
current is reduced to
100 µA. The device enters the TTL-standby mode
when CE# is at V
IH
. Maximum V
CC
current is reduced
to 1.0 mA. When in either standby mode, the device
places its outputs in a high-impedance state, indepen-
dent of the OE# input.
System Applications
During the switch between active and standby condi-
tions, transient current peaks are produced on the ris-
ing and falling edges of Chip Enable. The magnitude of
these transient current peaks is dependent on the out-
put capacitance loading of the device. At a minimum, a
0.1 µF ceramic capacitor (high frequency, low inherent
inductance) should be used on each device between
V
CC
and V
SS
to minimize transient effects. In addition,
to overcome the voltage drop caused by the inductive
effects of the printed circuit board traces on Express-
ROM device arrays, a 4.7 µF bulk electrolytic capacitor
should be used between V
CC
and V
SS
for each eight
devices. The location of the capacitor should be close
to where the power supply is connected to the array.
Output OR-Tieing
To accommodate multiple memory connections, a
two-line control function provides:
s
Low memory power dissipation, and
s
Assurance that output bus contention will not occur.
MODE SELECT TABLE
Mode
Read
Output Disable
Standby (TTL)
Standby (CMOS)
CE#
V
IL
X
V
IH
V
CC
±
0.3 V
OE#/V
PP
V
IL
V
IH
X
X
Outputs
D
OUT
High Z
High Z
High Z
Note:
X = Either V
IH
or V
IL
.
4
Am27X512
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
OTP Products. . . . . . . . . . . . . . . . . . –65°C to +125°C
Ambient Temperature
with Power Applied. . . . . . . . . . . . . . –55°C to +125°C
Voltage with Respect to V
SS
All pins except V
CC
. . . . . . . . . –0.6 V to V
CC
+ 0.6 V
V
CC
(Note 1). . . . . . . . . . . . . . . . . . . . . –0.6 V to 7.0 V
OPERATING RANGES
Commercial (C) Devices
Ambient Temperature (T
A
) . . . . . . . . . . .0°C to +70°C
Industrial (I) Devices
Ambient Temperature (T
A
) . . . . . . . . .–40°C to +85°C
Supply Read Voltages
V
CC
for ± 5% devices . . . . . . . . . . +4.75 V to +5.25 V
V
CC
for ± 10% devices . . . . . . . . . +4.50 V to +5.50 V
Operating ranges define those limits between which the func-
tionality of the device is guaranteed.
Note:
1. Minimum DC voltage on input or I/O pins –0.5 V. During
voltage transitions, the input may overshoot V
SS
to –2.0 V
for periods of up to 20 ns. Maximum DC voltage on input
and I/O pins is V
CC
+ 5 V. During voltage transitions, input
and I/O pins may overshoot to V
CC
+ 2.0 V for periods up
to 20 ns.
Stresses above those listed under “Absolute Maximum Rat-
ings” may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these
or any other conditions above those indicated in the opera-
tional sections of this specification is not implied. Exposure of
the device to absolute maximum ratings for extended periods
may affect device reliability.
Am27X512
5
京公网安备 11010802033920号
EEWORLD
