CMOS, Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD) Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD)
CMOS, Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD) Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD)
EP2645TTS-9.000M TR Parametric
Parameter Name
Attribute value
Brand Name
Ecliptek
Is it lead-free?
Lead free
Is it Rohs certified?
conform to
Parts packaging code
SMD 5.0mm x 7.0mm
Contacts
4
Manufacturer packaging code
SMD 5.0mm x 7.0mm
Reach Compliance Code
163
EP2645TTS-9.000M TR Preview
EP2645TTS-9.000M
EP26 45
Series
RoHS Compliant (Pb-free) 3.3V 4 Pad 5mm x 7mm
Ceramic SMD LVCMOS Programmable Oscillator
Frequency Tolerance/Stability
±50ppm Maximum
Operating Temperature Range
-20°C to +70°C
RoHS
Pb
Nominal Frequency
9.000MHz
T TS -9.000M
Pin 1 Connection
Tri-State (Disabled Output: High Impedance)
Duty Cycle
50 ±5(%)
ELECTRICAL SPECIFICATIONS
Nominal Frequency
Frequency Tolerance/Stability
9.000MHz
±50ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the
Operating Temperature Range,Supply Voltage Change, Output Load Change,
First Year Aging at 25°C, Shock, and Vibration)
±5ppm/year Maximum
-20°C to +70°C
3.3Vdc ±0.3Vdc
28mA Maximum (Unloaded)
Vdd-0.4Vdc Minimum (IOH= -8mA)
0.4Vdc Maximum (IOL= +8mA)
4nSec Maximum (Measured at 20% to 80% of waveform)
50 ±5(%) (Measured at 50% of waveform)
30pF Maximum
CMOS
Tri-State (Disabled Output: High Impedance)
70% of Vdd Minimum to enable output, 20% of Vdd Maximum to disable output, No Connect to enable
output.
20µA Maximum (Pin 1 = Ground)
16mA Maximum (Pin 1 = Ground)
±250pSec Maximum, ±100pSec Typical
±50pSec Maximum
10mSec Maximum
-55°C to +125°C
Aging at 25°C
Operating Temperature Range
Supply Voltage
Input Current
Output Voltage Logic High (Voh)
Output Voltage Logic Low (Vol)
Rise/Fall Time
Duty Cycle
Load Drive Capability
Output Logic Type
Pin 1 Connection
Tri-State Input Voltage (Vih and Vil)
Standby Current
Disable Current
Absolute Clock Jitter
One Sigma Clock Period Jitter
Start Up Time
Storage Temperature Range
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility
Fine Leak Test
Flammability
Gross Leak Test
Mechanical Shock
Moisture Resistance
Moisture Sensitivity
Resistance to Soldering Heat
Resistance to Solvents
Solderability
Temperature Cycling
Vibration
MIL-STD-883, Method 3015, Class 1, HBM: 1500V
MIL-STD-883, Method 1014, Condition A
UL94-V0
MIL-STD-883, Method 1014, Condition C
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 1004
J-STD-020, MSL 1
MIL-STD-202, Method 210, Condition K
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
MIL-STD-883, Method 1010, Condition B
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/17/2010 | Page 1 of 5
EP2645TTS-9.000M
MECHANICAL DIMENSIONS (all dimensions in millimeters)
PIN
CONNECTION
Tri-State (High
Impedance)
Ground/Case Ground
Output
Supply Voltage
7.00
±0.15
3
5.00
±0.15
MARKING
ORIENTATION
2
1.4 ±0.1
5.08
±0.15
4
2.20
±0.15
1
1.4 ±0.2
3.68
±0.15
1
2
3
4
LINE MARKING
1
2
3
ECLIPTEK
9.000M
PXXYZZ
P=Configuration Designator
XX=Ecliptek Manufacturing
Code
Y=Last Digit of the Year
ZZ=Week of the Year
1.60 ±0.20
Suggested Solder Pad Layout
All Dimensions in Millimeters
2.0 (X4)
2.2 (X4)
2.88
Solder Land
(X4)
1.81
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/17/2010 | Page 2 of 5
EP2645TTS-9.000M
OUTPUT WAVEFORM & TIMING DIAGRAM
TRI-STATE INPUT
V
IH
V
IL
CLOCK OUTPUT
V
OH
80% of Waveform
50% of Waveform
20% of Waveform
V
OL
OUTPUT DISABLE
(HIGH IMPEDANCE
STATE)
t
PLZ
Fall
Time
Rise
Time
T
W
T
Duty Cycle (%) = T
W
/T x 100
t
PZL
Test Circuit for CMOS Output
Oscilloscope
Frequency
Counter
+
+
Power
Supply
_
+
Voltage
Meter
_
Current
Meter
_
Supply
Voltage
(V
DD
)
Probe
(Note 2)
Output
0.01µF
(Note 1)
0.1µF
(Note 1)
Ground
C
L
(Note 3)
No Connect
or Tri-State
Note 1: An external 0.1µF low frequency tantalum bypass capacitor in parallel with a 0.01µF high frequency
ceramic bypass capacitor close to the package ground and V
DD
pin is required.
Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth
(>300MHz) passive probe is recommended.
Note 3: Capacitance value C
L
includes sum of all probe and fixture capacitance.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/17/2010 | Page 3 of 5
EP2645TTS-9.000M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
High Temperature Infrared/Convection
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
Additional Notes
3°C/second Maximum
150°C
175°C
200°C
60 - 180 Seconds
3°C/second Maximum
217°C
60 - 150 Seconds
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
20 - 40 seconds
6°C/second Maximum
8 minutes Maximum
Level 1
Temperatures shown are applied to body of device.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/17/2010 | Page 4 of 5
EP2645TTS-9.000M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
Low Temperature Infrared/Convection 240°C
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
Additional Notes
5°C/second Maximum
N/A
150°C
N/A
60 - 120 Seconds
5°C/second Maximum
150°C
200 Seconds Maximum
240°C Maximum
240°C Maximum 1 Time / 230°C Maximum 2 Times
10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
5°C/second Maximum
N/A
Level 1
Temperatures shown are applied to body of device.
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.)
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.)
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/17/2010 | Page 5 of 5
CMOS, Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD) Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD)
CMOS, Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD) Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 5.0mm x 7.0mm Ceramic Surface Mount (SMD)
It would be better if GD32F350 could support differential ADC. Everyone should know the reason. The work is almost finished. I am still busy writing the report. It is estimated that I have to submit t...
Set F553 key pulsePress P1.1, P1.4 generates a pulse, the time is 5s.Press P2.1, P1.4 generates a pulse, the time is 1.2s.#include msp430.h#include msp430f5529.h
/*** main.c* Set F553 key pulse* Press...
According to the United Nations Department of Economic and Social Affairs, by 2050, two-thirds of the world's population will live in cities. With the rapid advancement of urbanization, people can use...
Atmel Corporation has announced the launch of the highly integrated ATA6026 automotive driver IC, the first member of theupcoming automotive driver family. The ATA6026 is designed based on Atmel's hig...
EDGE (Enhanced Data Rates for GSM Evolution) is a standard for providing high-speed data services over existing GSM mobile phone networks. As the name implies, EDGE is based on the widely deployed GSM...
With the development of the times, Intel has been gradually replaced by single-chip microcomputers. In the past, Zilog, Motorola, and Intele were the three major players in the microprocessor field. B...
Target This event is a continuation of the November Student Zone; this time we will introduce current mirrors, whose output is not affected by changes in input current. Therefore, it will be helpf...[Details]
When high-
power
white light LEDs
are
used as new green lighting, they have advantages such as high light conversion efficiency, low power consumption, long life, and no maintenanc...[Details]
Recently, according to an announcement by Oriental Silver Star, the company plans to invest RMB 30 million to subscribe to the newly increased registered capital of Wuhan Minsheng; after the completi...[Details]
1 Introduction
One of the key technologies of EDA (electronic design automation) is to use hardware description language (HDL) to describe circuit systems, including circuit structure, behavio...[Details]
Introduction to the 6% (Ruhr) conical joint multi-function tester: It adopts a 7-inch colorful LCD touch screen with Chinese menu display. The nominal capacity of the syringe is selected through the ...[Details]
Teeth need to be brushed every day. Many people do not pay attention to oral hygiene, which can easily lead to residual bacteria and even accumulation of food residues. Over time, this may cause or...[Details]
Circuit principle: The integrated circuit charger, as shown in the figure, is a constant current charging circuit composed of a three-terminal voltage regulator (LM317). Since the potential differ...[Details]
I want to convert the PLC ladder diagram into an STL program, but how can I prevent the STL program from being restored to a LAD program?
A: ---------A relatively simple method is that a...[Details]
The adaptive pulse code modulation method changes the digital quantity according to the conversion rate of the voice analog signal, that is, in the pulse code modulation method, the quantization am...[Details]
One of the main challenges facing power engineers today is that as commercial electronic products become increasingly versatile and their size continues to shrink, there is less and less space left...[Details]
According to morning rumors, following the Mate 30 series, Huawei will launch a more innovative full-screen mobile phone on October 17, which may also be equipped with the Hongmeng system. "All sta...[Details]
According to Huanqiu.com, Flextronics, a well-known US listed foundry company with factories in Zhuhai, China, once privately detained materials and equipment worth RMB 700 million from Huawei afte...[Details]
Since the RS-422 bus has the characteristics of strong anti-interference ability, high communication rate, long communication distance, and can communicate with multiple slaves, the bus is widely u...[Details]
At the Huawei P30 series new product launch conference, Huawei also brought some interesting trendy items, such as cooperative smart glasses. The secret of smart glasses is in the glasses le...[Details]
Abstract: AD974 is the first 200kSPS, 4-channel, 16-bit data acquisition system produced by American Analog Devices. It has the characteristics of high throughput, low power consumption, high pr...[Details]
GD32 MCU
京公网安备 11010802033920号
EEWORLD
