Shelf product is a high-performance 1M byte (8Mbit) CMOS
static RAM built with two individual 524,288 x 8 bit SRAMs
with a common output enable. Memory access and control is
provided by an active LOW chip enable (En), an active LOW
output enable (G). This device has a power-down feature that
reduces power consumption by more than 90% when deselected.
Writing to each memory is accomplished by taking one of the
chip enable (En) inputs LOW and write enable (Wn) inputs
LOW. Data on the I/O pins is then written into the location
specified on the address pins (A
0
through A
18
). Reading from
the device is accomplished by taking one of the chip enable (En)
and output enable (G) LOW while forcing write enable (Wn)
HIGH. Under these conditions, the contents of the memory
location specified by the address pins will appear on the I/O pins.
Only one SRAM can be read or written at a time.
The input/output pins are placed in a high impedance state when
the device is deselected (En HIGH), the outputs are disabled (G
HIGH), or during a write operation (En LOW and Wn LOW).
E
1
A(18:0)
G
512K x 8
W
1
E
0
W
0
512K x 8
DQ(7:0)
Figure 1. UT8Q1024K8 SRAM Block Diagram
1
DEVICE OPERATION
NC
NC
A0
A1
A2
A3
A4
E1
DQ0
DQ1
V
DD
V
S S
DQ2
DQ3
W1
A5
A6
A7
A8
A9
W2
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
NC
E2
NC
A18
A17
A16
A15
G
DQ7
DQ6
V
SS
V
DD
DQ5
DQ4
A14
A13
A12
A11
A10
NC
NC
NC
Each die in the UT8Q1024K8 has three control inputs called
Enable (En), Write Enable (Wn), and Output Enable (G); 19
address inputs, A(18:0); and eight bidirectional data lines,
DQ(7:0). The device enable (En) controls device selection,
active, and standby modes. Asserting En enables the device,
causes I
DD
to rise to its active value, and decodes the 19 address
inputs to each memory die . Wn controls read and write
operations. During a read cycle, G must be asserted to enable
the outputs.
Table 1. Device Operation Truth Table
G
X
1
X
Wn
X
0
1
1
En
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
Figure 2. 25ns SRAM Pinout (44)
1
0
PIN NAMES
A(18:0)
DQ(7:0)
En
Wn
G
V
DD
V
SS
Address
Data Input/Output
Device Enable
WriteEnable
Output Enable
Power
Ground
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of Wn greater than V
IH
(min) with En and G less
than V
IL
(max) defines a read cycle. Read access time is
measured from the latter of device enable, output enable, or valid
address to valid data output.
SRAM Read Cycle 1, the Address Access is initiated by a change
in address inputs while the chip is enabled with G asserted and
Wn deasserted. Valid data appears on data outputs DQ(7:0) after
the specified t
AVQV
is satisfied. Outputs remain active
throughout the entire cycle. As long as device enable and output
enable are active, the address inputs may change at a rate equal
to the minimum read cycle time (t
AVAV
).
SRAM Read Cycle 2, the Chip Enable-controlled Access is
initiated by En going active while G remains asserted, Wn
remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQ(7:0).
SRAM Read Cycle 3, the Output Enable-controlled Access is
initiated by G going active while En is asserted, Wn is
deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
2
Notes:
1. To avoid bus contention, on the DQ(7:0) bus, only one En can be driven low
simultaneously while G is low.
WRITE CYCLE
A combination of Wn less than V
IL
(max) and En less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when eitherG is greater than V
IH
(min), or when Wn is less
than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access is defined
by a write terminated by Wn going high, with En still active.
The write pulse width is defined by t
WLWH
when the write is
initiated byWn, and by t
ETWH
when the write is initiated by En.
Unless the outputs have been previously placed in the high-
impedance state byG, the user must wait t
WLQZ
before applying
data to the eight bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable-controlled Access is defined by
a write terminated by the former of En or Wn going inactive.
The write pulse width is defined by t
WLEF
when the write is
initiated by Wn, and by t
ETEF
when the write is initiated by the
En going active. For the Wn initiated write, unless the outputs
have been previously placed in the high-impedance state by G,
the user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQ(7:0) to avoid bus contention.
TYPICAL RADIATION HARDNESS
The UT8Q1024K8 SRAM incorporates features which allow
operation in a limited radiation environment.
Table 2. Typical Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
50
<1E-8
krad(Si) nominal
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.5 to 4.6V
-0.5 to 4.6V
-65 to +150°C
1.0W (per byte)
+150°C
10°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. E xposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175
°C
during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
3.0 to 3.6V
-40 to +125°C
0V to V
DD
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(-40°C to +125°C) (V
DD
= 3.3V + 0.3)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN 1
C
IO 1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
(CMOS)
(CMOS)
I
OL
= 8mA, V
DD
=3.0V
I
OL
= 200µA,V
DD
=3.0V
I
OH
= -4mA,V
DD
=3.0V
I
OH
= -200µA,V
DD
=3.0V
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
SS
< V
IN
< V
DD,
V
DD
= V
DD
(max)
0V < V
O
< V
DD
V
DD
= V
DD
(max)
G = V
DD
(max)
I
OS2, 3
I
DD
(OP)
Short-circuit output current
Supply current operating
@ 1MHz
0V < V
O
< V
DD
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
I
DD1
(OP)
Supply current operating
@40MHz
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
I
DD2
(SB)
Nominal standby supply current
@0MHz
Inputs: V
IL
= V
SS
I
OUT
= 0mA
En = V
DD
- 0.5,
V
DD
= V
DD
(max)
V
IH
= V
DD
- 0.5V
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 101 9 .
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
The lower computer mainly outputs 1mA constant current to AIN5, but I don't know why the output current is inaccurate. When it is within 200uA, the actual measurement is very accurate, but when it exc...
[font="][size=11.0pt]Almost every embedded device has a debugging serial port. In some scenarios, it is inconvenient to connect to the PC with a physical cable, and a wireless connection is required. ...
I am planning now,,, basically considering Beijing, Chengdu, Chongqing, Hunan,,, I am a Shanghai native,,,,,,,,, I have a house in Shanghai,,,,,,,,,...
Live broadcast time:
May 19 (Tuesday) 14:00-16:10Live broadcast topic:
Key points to note in new energy vehicle power designContents:
New energy vehicles have undoubtedly become the hottest technical ...
On April 16, Dogecoin surged 100%. Is the sudden surge related to Musk's support? I don't know and I'm too lazy to find out.Yesterday I researched how to mine. I mined more than 6 in less than 24 hour...
[align=left][color=rgb(85, 85, 85)][font=微软雅黑][size=12px]When the switching power supply is in working state, the electric energy is pumped from the input end to the output end in each switching proce...
On December 10, Li Auto held a smart software conference, during which Li Auto officially launched the latest OTA 5.0 version, which includes smart driving (AD Max 3.0), smart space (SS 3.0) and smar...[Details]
Since there are no complex mechanical structures such as engines and gearboxes, many people think that electric vehicles have no technical content. In fact, this view is somewhat one-sided. In additi...[Details]
1. LED pin forming method
1 The bracket must be bent 2 mm away from the colloid.
2 The bracket forming must be done with a clamp or by a professional.
...[Details]
The E5061B ENA series network analyzers provide a wide frequency range from 5Hz to 3GHz. It supports not only general RF applications (such as filter or amplifier measurements, etc.), but also low-fr...[Details]
In March, two
robot
A-share listed companies sparked heated discussions in the market.
On one hand, the gear leader Shuanghuan Transmission is accelerating the "spin-off" of its precis...[Details]
As an engineer in the field of power electronics, you often need to use a digital oscilloscope to measure related electrical signals. There are also many types of probes that match the oscilloscope, ...[Details]
Recently, Japan and South Korea held a bilateral meeting at the WTO headquarters in Geneva. They failed to reach an agreement on Japan's strengthening of controls on South Korean semiconductors and o...[Details]
Recently, news came from the certification department that the photovoltaic grid-connected inverter of Samil New Energy Co., Ltd. (hereinafter referred to as "Samil New Energy") has once again obta...[Details]
Configuring the Memory Controller - SDRAM Programming Configuration
The 2440 memory controller has a total of 13 registers.
BANK0--BANK5 only need to set two registers: BWSCON and BANKCON...[Details]
As a display device, LED has been increasingly used in more and more fields due to its advantages such as high luminous efficiency, long service life and easy control. Especially since 2005, it h...[Details]
All digital circuits rely on clock signals to synchronize the operation of components. The number of times a circuit can operate per unit time depends on the frequency of the clock. Therefore, the fre...[Details]
Overview
With the rapid development of economy and the improvement of people's living standards, the number of cars has increased year by year, but it has also led to the worsening traffic...[Details]
With the continuous advancement of science and technology and the transformation of the global energy structure, the automotive power system is undergoing unprecedented changes. From traditional fu...[Details]
DigiKey Technology Zone
京公网安备 11010802033920号
EEWORLD
