PH1-SLPLA2842 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-SLPLA2842

PH1-SLPLA2842: DescriptionTransponder, LC/SPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-SLPLA2842 Overview

Transponder, LC/SPC Connector,

PH1-SLPLA2842 Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	unknown
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body width	56.1 mm
body height	13.2 mm
Body length or diameter	76.5 mm
Communication standards	OC-192, SONET
Connection Type	LC/SPC CONNECTOR
Emitter/Detector Type	PIN PHOTODIODE
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1533 nm
Nominal optical power output	1.584 mW
minimum return loss	-27 dB
Sensitivity	-17 dBm

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

External circuit structure of CPU clock circuit

LT1111 working principle diagram (b)

Reference source circuit diagram using LT1495 op amp

electronic House pet

Roxy M15M movement protection circuit

4～4.6MHz tuner

Free application: Fudan Micro FM33LG0 series, evaluation of Winsilver chip: Development board model: FM33LG0 series development board (5 in total) From: Fudan Micro The left picture is a real shot of the evaluation board, and the right picture is a close-up of the silver chip...; EEWORLD社区 Domestic Chip Exchange

Electromagnetic flowmeter selection considerations: 1. The electromagnetic flowmeter has requirements for straight pipes before and after installation, but the requirements are lower than those of other types of flowmeters, but the most important point...; cfybhd Sensor

In multisim simulation, what should I do if I encounter a device that is not in the circuit?: For example, can Goldensun's AC-DC, DC-DC modules, and varistors be replaced by ordinary resistors?...; 西里古1992 Analog electronics

Reservoir control system information: [i=s]This post was last edited by Rambo on 2019-7-19 14:30[/i]AbstractIn terms of water resource utilization, the measurement of flow, water quality and other parameters is very important, but many re...; 兰博 Electronics Design Contest

The problem of resistance in circuit: This is a well-functioning optocoupler isolation relay driver circuit.Let's focus on the R1 resistor in the circuit. What is the role of this resistor in the circuit? Do you have any other good design...; bigbat MCU

Filtering Problems in H-bridge Driving Circuit: This is a three-phase motor H-bridge drive circuit.In the filter circuit composed of D1 and C1 in the figure, why is there a resistor R1 in parallel? My analysis is that it is intended to form a volta...; bigbat Power technology

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components