TDA8029HL/C103,118 datasheet, PDF

TDA8029

Low power single card reader

Rev. 03 — 22 February 2005

Product data sheet

1. General description

The TDA8029 is a complete one chip, low cost, low power, robust smart card reader. Its

different power reduction modes and its wide supply voltage range allow its use in

portable equipment. Due to speciﬁc versatile hardware, a small embedded software

program allows the control of most cards available in the market. The control from the host

may be done through a standard serial interface.

The TDA8029 may be delivered with standard embedded software, or be masked with

speciﬁc customer code. For details on software development and on available tools,

please refer to application notes

“AN01009”

and

“AN10134”

for the TDA8029HL/C1. For

standard embedded software, please refer to

“AN10206”

for the TDA8029HL/C2.

2. Features

s

80C51 core with 16 kB ROM, 256 byte RAM and 512 byte XRAM

s

Speciﬁc ISO7816 UART, accessible with MOVX instructions for automatic convention

processing, variable baud rate, error management at character level for T = 0 and

T = 1 protocols, extra guard time, etc.

s

Speciﬁc versatile 24-bit Elementary Time Unit (ETU) counter for timing processing

during Answer To Reset (ATR) and for T = 1 protocol

s

V

CC

generation with controlled rise and fall times:

x

5 V

±

5 %, maximum current 65 mA

x

3 V

±

5 %, maximum current 50 mA; maximum current 65 mA if V

DD

> 3 V

x

1.8 V

±

5 %, maximum current 30 mA

s

Card clock generation up to 20 MHz with three times synchronous frequency doubling

(f

XTAL

,

1

⁄

2

f

XTAL

,

1

⁄

4

f

XTAL

and

1

⁄

8

f

XTAL

)

s

Card clock stop HIGH or LOW or 1.25 MHz from an integrated oscillator for card power

reduction modes

s

Automatic activation and deactivation sequences through an independent sequencer

s

Supports asynchronous protocols T = 0 and T = 1 in accordance with:

x

ISO 7816

and

EMV 3.1.1

(TDA8029HL/C1 and TDA8029HL/C2)

x

ISO 7816

and

EMV 2000

(TDA8029HL/C2).

s

1 to 8 characters FIFO in reception mode

s

Parity error counter in reception mode and in transmission mode with automatic

retransmission

s

Versatile 24-bit time-out counter for ATR and waiting times processing

s

Speciﬁc ETU counter for Block Guard Time (BGT) (22 ETU in T = 1 and 16 ETU in

T = 0)

Philips Semiconductors

TDA8029

Low power single card reader

s

Minimum delay between two characters in reception mode:

x

In protocol T = 0:

12 ETU (TDA8029HL/C1)

11.8 ETU (TDA8029HL/C2).

x

In protocol T = 1:

11 ETU (TDA8029HL/C1)

10.8 ETU (TDA8029HL/C2).

s

Supports synchronous cards which do not use C4/C8

s

Current limitations on card contacts

s

Supply supervisor for power-on/off reset and spikes killing

s

DC-to-DC converter (supply voltage from 2.7 to 6 V), doubler, tripler or follower

according to V

CC

and V

DD

s

Shut-down input for very low power consumption

s

Enhanced ESD protection on card contacts (6 kV minimum)

s

Software library for easy integration

s

Communication with the host through a standard full duplex serial link at

programmable baud rates

s

One external interrupt input and four general purpose I/Os.

3. Applications

s

Portable card readers

s

General purpose card readers

s

EMV compliant card readers.

4. Quick reference data

Table 1:

Symbol

V

DD

V

DCIN

I

DD(sd)

I

DD(pd)

Quick reference data

Parameter

supply voltage

NDS conditions

input voltage for the

DC-to-DC converter

supply current in Shut-down V

DD

= 3.3 V

mode

supply current in

Power-down mode

supply current in Sleep

mode

V

DD

= 3.3 V; card inactive;

microcontroller in

Power-down mode

V

DD

= 3.3 V; card active at

V

CC

= 5 V; clock stopped;

microcontroller in

Power-down mode;

I

CC

= 0 A

I

CC

= 65 mA;

f

XTAL

= 20 MHz;

f

CLK

= 10 MHz; 5 V card;

V

DD

= 2.7 V

Conditions

Min

2.7

3

V

DD

-

Typ

-

Max Unit

6.0

20

110

V

µA

I

DD(sl)

-

800

µA

I

DD(om)

supply current in operating

mode

-

250

mA

9397 750 14145

Product data sheet

Rev. 03 — 22 February 2005

2 of 59

Philips Semiconductors

TDA8029

Low power single card reader

Quick reference data

…continued

Parameter

card supply voltage

Conditions

active mode; I

CC

< 65 mA;

5 V card

active mode; I

CC

< 65 mA if

V

DD

> 3.0 V else

I

CC

< 50 mA; 3 V card

active mode; I

CC

< 30 mA;

1.8 V card

active mode; current pulses

of 40 nAs with I < 200 mA,

t < 400 ns, f < 20 MHz; 5 V

card

active mode; current pulses

of 40 nAs with I < 200 mA,

t < 400 ns, f < 20 MHz; 3 V

card

active mode; current pulses

of 12 nAs with I < 200 mA,

t < 400 ns, f < 20 MHz;

1.8 V card

Min

Typ

Max Unit

5.25 V

3.20 V

4.75 5

2.80 3

Table 1:

Symbol

V

CC

1.62 1.8

4.6

-

1.98 V

5.3

V

2.75 -

3.25 V

1.62 -

1.98 V

I

CC

card supply current

5 V card; V

CC

= 0 V to 5 V

3 V card; V

CC

= 0 V to 3 V;

V

DD

> 3.0 V

3 V card; V

CC

= 0 V to 3 V;

V

DD

< 3.0 V

1.8 V card; V

CC

= 0 V to

1.8 V;

-

100

65

50

30

-

mA

I

CC(det)

overload detection current

maximum load capacitor

300 nF

SR

r

, SR

f

rise and fall slew rate on

V

CC

t

de

t

act

f

XTAL

deactivation sequence

duration

activation sequence

duration

crystal frequency

0.05 0.16 0.22 V/µs

-

100

225

27

16

27

+90

µs

MHz

°C

V

DD

= 5 V

V

DD

< 3 V

external input

4

0

−40

T

amb

ambient temperature

5. Ordering information

Table 2:

Ordering information

Package

Name

TDA8029HL/C1

TDA8029HL/C2

LQFP32

Description

plastic low proﬁle quad ﬂat package; 32 leads;

body 7

×

7

×

1.4 mm

Version

SOT358-1

Type number

9397 750 14145

Product data sheet

Rev. 03 — 22 February 2005

3 of 59

Philips Semiconductors

TDA8029

Low power single card reader

6. Block diagram

V

DD

CDEL

6

RESET

SDWN_N

28

5

SUPPLY

SUPERVISOR

DC-to-DC

CONVERTER

CLOCK

CIRCUITRY

80C51

CONTROLLER

16 kB ROM

256 byte RAM

TIMER 2

18

16

P16

P17

P27

P26

P30/RX

P31/TX

EA_N

ALE

PSEN_N

2

1

24

25

32

31

21

P00/P07

22

P20

23

ISO 7816

UART

ANALOG

DRIVERS

AND

SEQUENCER

3

SAM

19

SAP SBM

14

17

SBP

15

13

VUP

220 nF

P33/INT1_N

30

PGND

DCIN

10

µF

24-bit

ETU

COUNTER

11

9

VCC

GNDC

12

10

7

P37

P25

RST

CLK

I/O

PRES

29

P32/INT0_N

CS

8

TEST

20

512 byte XRAM

27

26

CRYSTAL

OSCILLATOR

CONTROL/

STATUS

REGISTERS

INTERNAL

OSCILLATOR

XTAL2

XTAL1

TDA8029

4

fce869

GND

Fig 1. Block diagram

9397 750 14145

Product data sheet

Rev. 03 — 22 February 2005

4 of 59

Philips Semiconductors

TDA8029

Low power single card reader

7. Pinning information

7.1 Pinning

29 P32/INT0_N

30 P33/INT1_N

32 P30/RX

31 P31/TX

28 RESET

27 XTAL2

26 XTAL1

P17

P16

V

DD

GND

SDWN_N

CDEL

I/O

PRES

1

2

3

4

5

6

7

8

CLK 10

V

CC

11

RST 12

VUP 13

SAP 14

SBP 15

DCIN 16

9

25 P26

24 P27

23 PSEN_N

22 ALE

21 EA_N

20 TEST

19 SAM

18 PGND

17 SBM

001aac157

TDA8029HL

Fig 2. Pin conﬁguration

7.2 Pin description

Table 3:

Symbol

P17

P16

V

DD

GND

SDWN_N

CDEL

I/O

PRES

Pin description

1

2

3

4

5

6

7

8

Type

I/O

power

I

I/O

I

Description

general purpose I/O

supply voltage

ground connection

shut-down signal input (active LOW, no internal pull-up)

connection for an external capacitor determining the

power-on reset pulse width (typically 1 ms per 2 nF)

data input/output to/from the card (C7); 14 kΩ integrated

pull-up resistor to V

CC

card presence detection contact (active HIGH); do not

connect to any external pull-up or pull-down resistor; use

with a normally open presence switch (see details in

Section 8.13)

card ground (C5); connect to GND in the application

clock to the card (C3)

card supply voltage (C1)

card reset (C2)

output of the DC-to-DC converter (low ESR 220 nF to

PGND)

GNDC

CLK

V

CC

RST

VUP

9

10

11

12

13

power

O

power

9397 750 14145

Product data sheet

Rev. 03 — 22 February 2005

GNDC

5 of 59

TDA8029HL/C103,118

TDA8029HL/C103,118 Overview

Preview

TDA8029HL/C103,118 Related Products

Recommended Resources