REVISION G
DO NOT
SCALE FROM
THIS PRINT
Pb THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
RX402-XXXXX-XXXXX-XXXX
OPTION
F: SEMI FLEXIBLE
*R: SEMI RIGID
(SEE NOTE 10)
CABLE STRIPPING DIMENSIONS
PER CONFIGURATIONS
(SEE NOTES 12,13,14)
"A" mm
"B" mm
C
FIG 2
CABLE CALLOUT
402: CCA-402-X(RG-402 COAXIAL CABLE)
END 1 CONNECTOR
-01SP: SMA-P-C-XX-ST-CA9 (SEE SHEET 2)
-01RP: SMA-P-C-XX-RA-CA9 (SEE SHEET 2)
* -92SJ: 292XX-J-C-XX-ST-CA9 (SEE SHEET 2)
* -92SP: 292XX-P-C-XX-ST-CA9 (SEE SHEET 2)
END 1 PLATING OPTION
1: GOLD ALL COMPONENTS
4: ALTERNATE GOLD /GOLD FLASH/ NICKEL
6. ALTERNATE H GOLD / H GOLD / NICKEL
7. ALTERNATE GOLD MEDIUM/ GOLD FLASH
9. ALTERNATE HEAVY GOLD/MEDIUM GOLD
P: HEAVY GOLD / PASSIVATED STAINLESS STEEL
(SEE SHEET 2 FOR PLATING SPECIFICS)
OVERALL CABLE LENGTH
MILLIMETERS OF CABLE (SEE NOTES 8 & 9)
0100 MIN - 1000 MAX FOR RF402 (SEMI-
FLEXIBLE)
0100 MIN - 0305 MAX FOR RR402 (SEMI-RIGID)
END 2 PLATING OPTION
1: GOLD ALL COMPONENTS
4: ALTERNATE GOLD /GOLD FLASH/ NICKEL
6. ALTERNATE H GOLD / H GOLD / NICKEL
7. ALTERNATE GOLD MEDIUM/ GOLD FLASH
9. ALTERNATE HEAVY GOLD/MEDIUM GOLD
P: HEAVY GOLD / PASSIVATED STAINLESS STEEL
(SEE SHEET 2 FOR PLATING SPECIFICS)
(LEAVE BLANK FOR -SING OR -XXXX
END 2 PREPARATION)
END 2 CONNECTOR OR PREPARATION
-01SP: SMA-P-C-XX-ST-CA9 (SEE SHEET 2)
-01RP: SMA-P-C-XX-RA-CA9 (SEE SHEET 2)
* -92SJ: 292XX-J-C-XX-ST-CA9 (SEE SHEET 2)
* -92SP: 292XX-P-C-XX-ST-CA9 (SEE SHEET 2)
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)
-XXXX : STRIPPED AND TINNED (THIS END ONLY-
SEE NOTES 11-16 & SHEET 2, FIG 3)
(SEE FIG 2) "B" FORMAT: X.X mm
(SEE FIG 2) "A" FORMAT: X.X mm
DO NOT LEAVE ANY SPACE BLANK,
EACH MUST CONTAIN A
NUMERIC CHARACTER 0 THRU 9.
"D" mm
C
* = NOT RELEASED
*
*
NOTES:
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. CABLE CUT LENGTH:
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2).
(SEE TABLE 1 FOR SUBTRACTORS)
3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS.
4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1, THE TEST VOLTAGE FOR THE ASSEMBLY
SHOULD BE SET TO THE END OPTION WITH THE LOWEST TEST VOLTAGE RATING.
5. AFTER FINAL ELECTRICAL TESTS, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL -ET.
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3040-M.
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS.
9. CABLE LENGTHS LONGER THAN 1000 MILLIMETERS ARE NOT SUPPORTED BY S.I. TEST DATA.
10. MINIMUM BEND RADIUS FOR RF402 = 6.35 [0.250],
RR402 SUPPLIED AS STRAIGHT ASSEMBLIES ONLY, WITH MAX LENGTH = 585[23"].
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.
12. DIM "A" AND "B" HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm.
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A.
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B.
15. NOTE DELETED.
16. FOR STRIPPED AND TINNED OPTION, ONLY THE CENTER CONDUCTOR IS TINNED.
17. CONNECTORS TO BE ORIENTED ACCORDING TO CO-HD-WI-3048-M.
C
C
C
RF402-01SPX-01RPX-XXXX SHOWN
FIG 1
F:\DWG\MISC\MKTG\RX402-XXXXX-XXXXX-XXXX -MKT.SLDDRW
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
MILLIMETERS [INCHES].
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
TOLERANCES ARE:
DECIMALS
.X: 0.3 [.01]
2
.XX: 0.13 [.005]
.XXX: 0.051 [.0020]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
MATERIAL:
SEE END 1 AND END 2 ASSEMBLY PRINTS
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
RF402 OR RR402 CABLE ASSEMBLY
RX402-XXXXX-XXXXX-XXXX
01/11/2011
BY:
ALVIN W
SHEET
1
OF
2
REVISION G
(STRAIGHT PLUG)
-01SP
(RIGHT ANGLE PLUG)
(USE DRAWING No. SMA-P-C-XX-RA-CA9
FOR ASSEMBLY INSTRUCTIONS)
-01RP
(USE DRAWING No. SMA-P-C-XX-ST-CA9
FOR ASSEMBLY INSTRUCTIONS)
PLATING OPTIONS
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-P-C-HF-ST-CA9)
4: 10μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-P-C-GN-ST-CA9)
7: 10μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-P-C-GF-ST-CA9)
NOTE: ALL CRITICAL DIMENSIONS ON SMA-P-C-XX-ST-CA9
THAT APPLY MUST BE VERIFIED.
*
-92SJ
(STRAIGHT JACK)
(USE DRAWING No. 292XX-J-C-XX-ST-CA9
FOR ASSEMBLY INSTRUCTIONS)
PLATING OPTIONS
1: 30μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-P-C-HF-RA-CA9)
4: 10μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
100μ" MIN. NICKEL REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-P-C-GN-RA-CA9)
7: 10μ" MIN. GOLD CENTER CONTACT
3μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: SMA-P-C-GF-RA-CA9)
NOTE: ALL CRITICAL DIMENSIONS ON SMA-P-C-XX-RA-CA9
THAT APPLY MUST BE VERIFIED.
*
-92SP
(STRAIGHT PLUG)
(USE DRAWING No. 292XX-P-C-XX-ST-CA9
FOR ASSEMBLY INSTRUCTIONS)
2.00 .079
2.50 .098
4.50 .177
RX402-01SPX-2025-XXXX SHOWN
FIG 3
PLATING OPTIONS
6: 30μ" MIN. GOLD CENTER CONTACT
30μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PB-J-C-HH-ST-CA9)
9: 30μ" MIN. GOLD CENTER CONTACT
10μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PB-J-C-HG-ST-CA9)
P: 30μ" MIN. GOLD CENTER CONTACT
PASSIVATED STAINLESS STEEL OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PS-J-C-HP-ST-CA9)
NOTE: ALL CRITICAL DIMENSIONS ON 292XX-J-C-XX-ST-CA9
THAT APPLY MUST BE VERIFIED.
PLATING OPTIONS
6: 30μ" MIN. GOLD CENTER CONTACT
30μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PB-P-C-HH-ST-CA9)
9: 30μ" MIN. GOLD CENTER CONTACT
10μ" MIN. GOLD OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PB-P-C-HG-ST-CA9)
P: 30μ" MIN. GOLD CENTER CONTACT
PASSIVATED STAINLESS STEEL OUTER CONTACT
3μ" MIN. GOLD REMAINING METAL PARTS
(END CONNECTOR P/N: 292PS-P-C-HP-ST-CA9)
NOTE: ALL CRITICAL DIMENSIONS ON 292XX-P-C-XX-ST-CA9
THAT APPLY MUST BE VERIFIED.
F:\DWG\MISC\MKTG\RX402-XXXXX-XXXXX-XXXX -MKT.SLDDRW
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 1:1
RF402 OR RR402 CABLE ASSEMBLY
RX402-XXXXX-XXXXX-XXXX
01/11/2011
BY:
ALVIN W
SHEET
2
OF
2
京公网安备 11010802033920号
EEWORLD
