PH1-PI2FA296N datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-PI2FA296N

PH1-PI2FA296N: DescriptionTransponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-PI2FA296N Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,

PH1-PI2FA296N Parametric

Parameter Name	Attribute value
Maker	JDS Uniphase Corporation ( VIAVI )
Reach Compliance Code	unknown
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body width	56.1 mm
body height	13.2 mm
Body length or diameter	76.5 mm
Communication standards	GR-253
Connection Type	FC/UPC CONNECTOR
Data rate (receive)	10709 Mbps
Data rate (send)	10709 Mbps
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1536 nm
Nominal optical power output	1.122 mW
minimum return loss	-27 dB

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

High input impedance three op amp differential amplifier circuit diagram

Internal circuit of TM2001A

Magnetic controlled music notifier circuit

FET oxygen sensor measurement circuit

Five-function refrigerator protector

Wide range adjustable high voltage power supply circuit

[NXP Rapid IoT Review] +NO.1 First Hands-On Experience---Small but Fully Complementary: [i=s] This post was last edited by sipower on 2019-1-2 21:20 [/i] [align=left][font=宋体]【[/font]NXP Rapid IoT Review】+NO.1 First Hands-On Experience---Small but Complete[/align] [align=left][font=宋体]It...; sipower RF/Wirelessly

What parameters should be considered when evaluating and selecting SiC MOSFET devices?: The application scope of SiC power devices is becoming wider and wider, the switching frequency is getting higher and higher, and the requirements for devices are also getting higher and higher. How t...; eric_wang Integrated technical exchanges

Challenge FreeRTOS learning + How to port FreeRTOS and create tasks for STM32F107: I am a novice, and I will briefly describe how to port FreeRTOS to STM32F107 and create tasks.Using three software to implement FreeRTOS configurationSTMSTM32CubeMXAND EWARM V8.32FreeRTOS source codeS...; superstar_gu MCU

Please analyze this circuit. What will the final waveform be?: As shown in the figure below, when the S button is pressed once, a set of specified pulses is emitted. The three variable resistors are composed of digital potentiometers or 3296 adjustable resistors....; 灞波儿奔 Power technology

NFC chip selection and basic circuit framework: NFC chip selection and basic circuit frameworkRFID is a highly professional technology. Some companies may even recruit professional RFID engineers. This article only covers basic selection design, ci...; Jacktang Wireless Connectivity

【McQueen Trial】Python Programming (2): [i=s]This post was last edited by dcexpert on 2019-5-19 20:56[/i] [b]Buzzer[/b] By default, microbit uses pin0 to control the buzzer, which can be used to play music. [code]from microbit import * impo...; dcexpert MicroPython Open Source section

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components