CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
NPCAP
●
Super
TM
Surface Mount
-
low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
●
Rated voltage range : 2.5 to 25V
dc
, case size range :
φ
4
×
5.2L to
φ
10
×
12.2L
●
Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
●
RoHS Compliant
●
Halogen Free
PXA
Series
PXE
Lower ESR
PXA
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +105℃
2.5 to 25V
dc
±
20% (M)
Rated voltage
×
1.15 (Rated voltage 2.5 to 20V
dc
, 25V
dc
) / Rated voltage
×
1.00 (Rated voltage 23V
dc
)
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
Characteristics
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)
≦
1.15
Z(-55℃)/Z(+20℃)
≦
1.25
Bias Humidity
Surge Voltage
Failure Rate
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
(F46 : 1,000 hours) at 105℃.
Appearance
No significant damage
Capacitance change
≦±
20% of the initial value
≦
150% of the initial specified value
DF (tanδ
)
≦
150% of the initial specified value
ESR
Leakage current
≦
The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours(F46 : 500 hours).
Appearance
No significant damage
Capacitance change
≦±
20% of the initial value
≦
150% of the initial specified value
DF (tanδ
)
ESR
≦
150% of the initial specified value
≦
The initial specified value
Leakage current
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105
℃
for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±
20% of the initial value
DF (tanδ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105
℃
)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105
℃
.
◆DIMENSIONS
[mm]
●
Terminal
◆MARKING
W
P
C±
0.2
Size code
D55
E60
F46
F55
F60
H70
HC0
J80
JC0
Code : A
B±
0.2
0.3max.
A
±
0.2
L
±
0.3 (Note)
Note : L+0.1/-0.2 for F46
L
±
0.5 for HC0 and JC0
φ
D
4
5
6.3
6.3
6.3
8
8
10
10
B
C
L
A
5.2 4.3 4.3 5.1
5.7 5.3 5.3 5.9
4.5 6.6 6.6 7.2
5.2 6.6 6.6 7.2
5.7 6.6 6.6 7.2
6.7 8.3 8.3 9.0
12.0 8.3 8.3 9.0
7.7 10.3 10.3 11.0
12.2 10.3 10.3 11.0
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.0
1.4
1.9
1.9
1.9
3.1
3.1
4.5
4.5
EX) 16V39µF
◆PART
NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
A PXA
φD±
0.5
A
15L
39
16
V
A RA
M
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10μF:100,100μF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/2)
CAT. No. E1001M
京公网安备 11010802033920号
EEWORLD
