Min. 1,000 M (at 500 V DC) Measurement at same location as “Breakdown voltage” section.
1,000 Vrms for 1 min.
750 Vrms for 1 min.
1,000 Vrms for 1 min.
750 Vrms for 1 min.
4,000 Vrms for 1 min. (Detection current: 10 mA)
Max. 45C
113F
(By resistive method, nominal coil voltage
applied to the coil; contact carrying current:
5A, at 70C
158F)
Max. 45C
113F
(By resistive method, nominal coil voltage
applied to the coil; contact carrying current:
10A, at 70C
158F)
N.O.: 10 A, N.C.: 3 A
200 mW
400 mW
Temperature rise (coil)
Electrical
characteristics
Surge breakdown voltage*
2
(Between contact and coil) (Initial)
Operate time (at nominal voltage) (at 20C
68F)
(Initial)
Release time (at nominal voltage) (at 20C
68F)
(Initial)
Shock resistance
Mechanical
characteristics
Vibration resistance
Expected life
Functional
Destructive
Functional
Destructive
8,000 V
Max. 20 ms (excluding contact bounce time.)
Max. 10 ms (excluding contact bounce time) (Without diode)
294 m/s
2
(Half-wave pulse of sine wave: 11 ms; detection time: 10s.)
980 m/s
2
(Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 1.6 mm (Detection time: 10s.)
10 to 55 Hz at double amplitude of 2.0 mm
Min. 10
7
Ambient temperature: –40C to +70C
–40F to +158F
(class E insulation),
–40C to +85C
–40F to +185F*
4
(class B insulation)
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 times/min. (at nominal switching capacity)
Approx. 7 g
.25 oz
Mechanical (at 180 times/min.)
Conditions for operation, transport and storage*
3
Max. operating speed
Conditions
Unit weight
* Specifications will vary with foreign standards certification ratings.
Notes:
*1. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load.
*2. Wave is standard shock voltage of
1.250s
according to JEC-212-1981
*3.The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to “6. Usage, Storage and Transport
Conditions“ in
AMBIENT ENVIRONMENT section in Relay Technical Information.
*4. When using relays in a high ambient temperature, consider the pick-up voltage rise due to the high temperature (a rise of approx. 0.4% V for each 1C
33.8F
with 20C
68F
as a reference) and use a coil impressed voltage that is within the maximum applied voltage range.
[size=4][md]## Content Summary This article first briefly introduces the concept of bluetooth mesh, and then uses the development board to demonstrate the functions of Bluetooth mesh. ---- ## Introduc...
I would like to ask whether the output current in the data sheet refers to the output current of each channel or the total output current?And what does this +/-24mA refer to?...
[i=s]This post was last edited by Niubility-a on 2018-12-17 11:55[/i] [align=left]Android system architecture[/align][align=left]Android system architecture is the architecture of the Android system. ...
Question 1: How should the parameters of capacitors and resistors be selected in the square wave generator circuit?For example, given the peak-to-peak value and frequency, how should the parameters be...
Based on my current preliminary understanding of the industry, I feel that Mingyang Longyuan will be a dark horse in the next few years and will become the top domestic enterprise in a few years....
The setting of the spectrum analyzer's resolution bandwidth (RBW) must be carefully considered because it affects the separation of spectral components, the setting of an appropriate noise floor, and...[Details]
A new study finds that seismic sensors can detect fast-moving floodwaters heading toward them, The Verge reports. According to the authors of a recently published paper, this information is particula...[Details]
The Song Dynasty's "Pingjiang Map" is the earliest and most complete ancient inscribed city layout map in my country. Looking down from a satellite, people will be surprised that the current Suzhou...[Details]
Ⅰ. Write in front Compared with the previous 51 series chips, one of the advantages of the STM8S chip is that it has richer peripheral resources and more powerful functions. Therefore, this article ...[Details]
According to foreign media reports recently, the total cost of Huawei P30 Pro is about 363.83 US dollars. Subsequently, foreign media disassembled the P30 Pro, and the disassembly results showed that...[Details]
According to foreign media reports, two members of the U.S. House of Representatives are launching a bipartisan joint action to promote legislation for self-driving cars. Republican Reps. Robert La...[Details]
On September 26, the September major project launch event in Haining City, Jiaxing, Zhejiang Province was held in Haining Economic Development Zone, and the HiSilicon 300mm wafer production line proj...[Details]
From a plant physiological perspective, the micro-change dynamics of the volume of plant organs (stems, leaves, fruits, etc.) are related to the water status in their bodies. When the roots absorb su...[Details]
The long-term outlook for automotive battery chemistry is looking more and more like the future of aluminum batteries, with Saudi-backed Indian researchers Saturnose becoming the latest to join the a...[Details]
Currently, lightweight, deformable flexible materials are seen as a key breakthrough for intelligent electronic products, and are expected to give rise to many innovative applications. However, t...[Details]
"Splicing" chips seems to have become the new "fashion" in the chip circle. At Apple’s spring new product launch conference in March, it released the M1 Ultra, which is made by “gluing” two M1 Max...[Details]
On February 25, TSMC released its 2021 annual financial report. According to the report, TSMC's operating income in 2021 was NT$1.59 trillion, a year-on-year increase of 19%, and its net profit was N...[Details]
1. Working Principle After the power is turned on, the heating resistor is connected to the 220V AC circuit through the normally closed contact of the relay, and heating begins. At this time, th...[Details]
The window watchdog (WWDG) is used to detect software faults caused by external interfaces or unexpected logic operations. These faults will cause the program to interrupt normal operation. When a pr...[Details]
What is a contactor?
They are electromechanical switches that, while similar to relays, perform heavy-duty applications that require higher current carrying capabilities. Contactors provide lo...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
