EEWORLDEEWORLDEEWORLD

Part Number

Search

XC62FP3101PB

Description
IC,VOLT REGULATOR,FIXED,+5V,CMOS,TO-243,3PIN,PLASTIC
Categorysemiconductor    Power management   
File Size268KB,16 Pages
ManufacturerTOREX
Websitehttp://www.torex.co.jp/chinese/
Download Datasheet Parametric View All

XC62FP3101PB Overview

IC,VOLT REGULATOR,FIXED,+5V,CMOS,TO-243,3PIN,PLASTIC

XC62FP3101PB Parametric

Parameter NameAttribute value
Number of terminals3
each_compliYes
EU RoHS regulationsYes
stateContact Mf
AdjustableFIXED
dropout_voltage1_nom1 V
input_voltage_absolute_max12 V
line_regulation_max0.0600 V
load_regulation_max0.0800 V
Number of outputs1
Minimum operating temperature-40 Cel
Maximum operating temperature85 Cel
Maximum output current 10.1000 A
Rated output voltage 15 V
Packaging MaterialsPLASTIC/EPOXY
ckage_equivalence_codeTO-243
cking_methodTAPE&REEL (RIGHT)
qualification_statusCOMMERCIAL
sub_categoryOther Regulators
surface mountYES
CraftsmanshipCMOS
voltage_tolerance_max2 %
03S_05XC62FP 02.10.7 5:18 PM ページ 285
Series
Positive Voltage Regulators
NCMOS
Low Power Consumption
NSmall
Input-Output Voltage Differential
■Applications
GBattery
Powered Equipment
GPalmtops
: 0.12V @ 100mA,
GPortable
Cameras and Video Recorders
0.38V @ 200mA
GReference
Voltage Sources
NMaximum
Output Current : 250mA (V
OUT
=5.0V)
3
NOutput
Voltage Range
NHighly
Accurate
: 2.0V~6.0V
: ±2% (±1%)
■General Description
The XC62FP series is a group of positive voltage output, three-pin
regulators, that provide a high current even when the input/output
voltage differential is small. Low power consumption and high accuracy
is achieved through CMOS and laser trimming technologies.
The XC62FP consists of a high-precision voltage reference, an error
amplification circuit, and a current limited output driver. Transient
response to load variations have improved in comparison to the existing
series.
SOT-23 (150mW), SOT-89 (500mW) and TO-92 (300mW) packages are
available.
■Features
Maximum Output Current
: 250mA
(within max. power dissipation, V
OUT
= 5.0V)
Output Voltage Range
: 2.0V ~ 6.0V in 0.1V increments
(1.5V ~ 1.9V for custom products)
Highly Accurate:
Output voltage ±2%
(±1% for semi-custom products)
Low Power Consumption
: Typ. 2.0µA @ V
OUT
=5.0V
Output Voltage Temperature Characteristics
: Typ. ±100ppm/°C
Input Stability
: Typ. 0.2%/V
Small Input-Output Differential
: I
OUT
= 100mA @ V
OUT
= 5.0V with a
0.12V differential.
Ultra Small Packages
: SOT-23 (150mW) mini-mold,
SOT-89 (500mW) mini-power mold
TO-92 (300mW)
■Typical Application Circuit
V
IN
V
IN
V
ss
V
OUT
■Typical Performance
Characteristic
XC62FP3002 (3V)
3
Supply Current:Iss (µA)
C
IN
1µF
(Tantalum)
C
L
1µF
(Tantalum)
Topr=25℃
85℃
2
-40℃
1
R
L
0
0
2
4
6
8
10
Input Voltage:V
IN
(V)
285
[RVB2601 Creative Application Development] Short recording, playback and printing of recording data
[i=s]This post was last edited by onoff on 2022-6-4 18:01[/i]Refer to the examples on the official website, the SDK examples, and ch2601_ft_demo.I transplanted ft.c to my own project. The c file and s...
onoff XuanTie RISC-V Activity Zone
When the carrier data reaches the receiving end, how does the receiving end identify this information?
I would like to ask: For the signals composed of multiple identical waveforms as shown in 1, 2, and 3 in the following figure, when the carrier data reaches the receiving end, how does the receiving e...
深圳小花 MCU
SparkRoad Review (7) - FPGA Serial Port Test
Anlu's development board is equipped with a USB2UART module, which is connected to the USB-to-serial port through the microcontroller on the board. It is not possible to open the built-in routine 6_ua...
bigbat Domestic Chip Exchange
Disable AD auto-start JLink
After reinstalling AD, JLink suddenly stopped working. I found that JLink was automatically started when running AD.Just uncheck these two....
LinQian_Sun Embedded System
Seeking guidance - stc microcontroller remote upgrade program
I've been studying the remote upgrade function of stc microcontrollers recently. I searched online for some solutions proposed by predecessors, but I still feel confused. I have a question, so I'm her...
曹旭华 51mcu
Problems with creating sheet symbols for multi-page schematics
When AD designs a multi-page schematic, do I need to add a sheet symbol? design----create sheet symbol from sheet or HDL. I see that some designs have it added, but some designs have not....
平漂流 PCB Design

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号