REVISION U
VERTICAL
(HQCD-060-XX.XX-STR-STR-1 SHOWN)
FIG. 1
HQCD-XXX-XX.XX-XXX-XXX-X-X
No OF POSITIONS
-030, -060, -090, -120
(PER ROW)
LENGTH
-XX.XX (INCHES)
(03.75[95.3] MIN)
(SEE NOTE 2)
(SEE NOTE 8)
FIRST END
-TTR: TERMINAL, TOP, RIGHT
-TTL: TERMINAL, TOP, LEFT
-TBR: TERMINAL, BOTTOM, RIGHT
-TBL: TERMINAL, BOTTOM, LEFT
-STR: SOCKET, TOP, RIGHT
-STL: SOCKET, TOP, LEFT
-SBR: SOCKET, BOTTOM, RIGHT
-SBL: SOCKET, BOTTOM, LEFT
(SEE TABLE 1 & SHEET 2)
-TEU: TERMINAL, EDGE MOUNT, UP
-TED: TERMINAL, EDGE MOUNT, DOWN
-SEU: SOCKET, EDGE MOUNT, UP
-SED: SOCKET, EDGE MOUNT, DOWN
(SEE TABLE 5 & SHEET 4)
-TPU: TERMINAL, PANEL MOUNT, UP
-TPD: TERMINAL, PANEL MOUNT, DOWN
-SPU: SOCKET, PANEL MOUNT, UP
-SPD: SOCKET, PANEL MOUNT, DOWN
(SEE TABLE 11 & SHEET 6)
(ONLY AVAILABLE ON -030,-060, AND -090)
END OPTION
-F: SCREW OPTION FIRST END ONLY (NOT AVAILABLE
WITH XPX OPTIONS)
-S: SCREW OPTION SECOND END ONLY
-B: SCREW OPTION BOTH ENDS (NOT AVAILABLE
WITH XPX OPTIONS)
-N: NO CAPS
-L: FIRST END RT1 OPTION (SEE NOTES 9 & 10)
-R: SECOND END RT1 OPTION (SEE NOTES 9 & 10)
-D: BOTH ENDS RT1 OPTION (SEE NOTES 9 & 10)
-1: FIRST END SCREW OPTION,
SECOND END RT1 OPTION (SEE NOTES 9 & 10)
-2: FIRST END RT1 OPTION,
SECOND END SCREW OPTION (SEE NOTES 9 & 10)
(SEE FIG. 3, SHEET 5 FOR EDGE MOUNT
END OPTIONS)
(SEE FIG. 4, SHEET 5 FOR DOUBLE
VERTICAL END OPTIONS)
(SEE FIG. 5, SHEET 5 FOR NO CAPS)
(LEAVE BLANK FOR STANDARD CAPS
BOTH ENDS)
WIRING OPTION
-1: PIN 1 TO PIN 1
-2: PIN 1 TO PIN 2
-3: PIN 1 TO PIN N-1
-4: PIN 1 TO PIN N
(SEE TABLE 9, SHEET 6)
SECOND END
-TTR: TERMINAL, TOP, RIGHT
-TTL: TERMINAL, TOP, LEFT
-TBR: TERMINAL, BOTTOM, RIGHT
-TBL: TERMINAL, BOTTOM, LEFT
-STR: SOCKET, TOP, RIGHT
-STL: SOCKET, TOP, LEFT
-SBR: SOCKET, BOTTOM, RIGHT
-SBL: SOCKET, BOTTOM, LEFT
(SEE TABLE 1 & SHEET 3)
-TEU: TERMINAL, EDGE MOUNT, UP
-TED: TERMINAL, EDGE MOUNT, DOWN
-SEU: SOCKET, EDGE MOUNT, UP
-SED: SOCKET, EDGE MOUNT, DOWN
(SEE TABLE 5 & SHEET 4)
DO NOT
SCALE FROM
THIS PRINT
SUB-HQCD-X-XXX-XX-XX
01
LENGTH: XX.XX + "L" REF (SEE TABLE 4)
C1
LENGTH: XX.XX 1%
01
02
02
'A'
"A" REF
(TYP)
"B" REF
(TYP)
N-1
(SEE TABLE 3)
.565 14.35
REF (TYP)
.775 19.69 REF
(TYP)
N-1
(SEE TABLE 3)
N
(SEE TABLE 3)
N
(SEE TABLE 3)
SUB-HQCD-X-XXX-XX-XX
STS-01
(TIGHTEN TO 1.4 - 1.7 IN-LBS)
(4 PLCS)
QCD-XX-01
HDRL-11
(SEE NOTE 5)
.253 6.42 REF (TYP)
FIRST END
SECOND END
LENGTH REF
* "C" REF
NOTES:
C
REPRESENTS A CRITICAL DIMENSION.
1.
2. SUB-TCF LENGTH IS EQUAL TO HQCD LENGTH.
C2
3. ALL ASSEMBLIES TO BE 100% ELECTRICALLY TESTED
QCD-XX-02
FOR SHORTS AND OPENS.
SUB-TCF-3850-30-01-XX.XX
C3
4. ALL ASSEMBLIES TO BE 100% HI-POT TESTED AT 300V.
(SEE TABLE 1 FOR QTY)
5. TOP SUB-TCF NOT SHOWN IN THIS VIEW FOR CLARITY; HDRL-11 TO BE CENTERED ON LOWER
SUB-TCF AS SHOWN; HDRL-11 IS TO CONTAIN:
LINE 1 - PART NUMBER “HQCD-XXX-XX.XX-XXX-XXX-X-X”
LINE 2 - SHOP ORDER NUMBER “XXXXXX”
LINE 3 - DATE CODE “XXXXX”
THIS PRODUCT MANUFACTURED
Pb
6. FOR PACKAGING REQUIREMENTS REFERENCE PACKAGING STANDARDS.
WITH LEAD-FREE PROCESSING
* -DV END OPTIONS ONLY
7. PARTS TO BE PROCESSED PER SAMTEC ACCEPTABILITY
REQUIRMENTS: HDR-P1-01 "CABLE ASSEMBLY WORKMANSHIP STANDARDS".
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
8. CABLE LENGTHS LONGER THAN 40.00 INCHES ARE NOT SUPPORTED BY S.I. TEST DATA.
DIMENSIONS ARE IN INCHES.
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
9. RT1 OPTION IS NOT AVAILABLE WITH EDGEMOUNT OR PANEL MOUNT END OPTIONS.
TOLERANCES ARE:
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
10. RT1 OPTION IS NOT AVAILABLE WITH -120 POSITIONS.
DECIMALS
ANGLES
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
11. ALL POSITIONS TRANSMITTED AS SIGNALS ACROSS COAX CENTER CONDUCTORS. CONNECTOR
.XX: .01 [.3]
2
PURPOSE OTHER THAN THAT WHICH IT WAS
.XXX: .005 [.13]
GROUND BLADE TIED TO COAX SHIELD.
OBTAINED WITHOUT THE EXPRESSED WRITTEN
.XXXX: .0020 [.051]
CONSENT OF SAMTEC, INC.
DETAIL 'A'
SCALE 2.5 : 1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 1:0.8
DESCRIPTION:
DWG. NO.
0.5mm HIGH-SPEED COAX CABLE ASSEMBLY
HQCD-XXX-XX.XX-XXX-XXX-X-X
04/29/03
SHEET
1
OF
8
c:\enterprisevault\DWG\MISC\MKTG\HQCD-XXX-XX.XX-XXX-XXX-X-X-MKT.SLDDRW
BY:
KEVIN B
REVISION U
N-1
N
FIRST END - EDGE MOUNT (SEE TABLE 9, SHEET 7)
T1
SECOND END - EDGE MOUNT (SEE TABLE 9, SHEET 7)
-TED
T
B
T1
2
1
T
-TED
-TEU
B
-TEU
1
2
T30
T
B
N-1
N
B30
T30
T
B
N
N-1
B30
2
1
1
2
B1
T1
N
N-1
B1
N
N-1
-SEU
1
2
T1
-SED
T
B
1
B30
2
2
1
-SEU
-SED
T
N-1
N
T30
T
B
N-1
N
T30
T
B
B
B30
N
N-1
B1
B1
2
1
EDGE MOUNT (NO CAPTIVE PANEL SCREWS)
(HQCD-030-XX.XX-TEU-STR-X SHOWN)
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
LENGTH: XX.XX + "L" REF (SEE TABLE 4, SHEET 1)
.271 6.88
REF
FIG. 2
"D" REF
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
QCD-XX-03
SUB-HQCD-X-XXX-03-XX
c:\enterprisevault\DWG\MISC\MKTG\HQCD-XXX-XX.XX-XXX-XXX-X-X-MKT.SLDDRW
DO NOT SCALE DRAWING
SHEET SCALE: 1:1
0.5mm HIGH-SPEED COAX CABLE ASSEMBLY
DWG. NO.
HQCD-XXX-XX.XX-XXX-XXX-X-X
04/29/03
SHEET
4
OF
8
BY:
KEVIN B
REVISION U
EDGE MOUNT (WITH CAPTIVE PANEL SCREWS)
(HQCD-030-XX.XX-SEU-XXX-1-F SHOWN)
(SAME AS FIG. 2, UNLESS OTHERWISE STATED)
FIG. 3
DOUBLE VERTICAL (WITH SCREW DOWN OPTION)
(HQCD-030-XX.XX-TTR-XXX-1-F SHOWN)
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
.228 5.79
REF
.129 3.28 REF (TYP)
FIG. 4
"F" REF
"E" REF
"G" REF
"H" REF
"J" REF
QCD-XX-03-CPS
CPS-4-40-01-X
QCD-XX-02-SDO
.250 6.34
REF (TYP)
(HQCD-XXX-XX.XX-TEU-STR-1-N SHOWN)
(SAME AS FIG. 1 EXCEPT AS SHOWN)
SUB-HQCD-X-XXX-03-XX
SUB-TCF-3850-XX-01-XX.XX
SUB-HQCD-X-XXX-XX-XX
FIG. 5
"L"
(SEE TABLE 10)
"K"
(SEE TABLE 10)
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
APPLY UV EPOXY TO ALL CABLE ENDS
(HEIGHT NOT TO EXCEED .065[1.65] ABOVE PCB SURFACE)
c:\enterprisevault\DWG\MISC\MKTG\HQCD-XXX-XX.XX-XXX-XXX-X-X-MKT.SLDDRW
DO NOT SCALE DRAWING
SHEET SCALE: 1.25:1
0.5mm HIGH-SPEED COAX CABLE ASSEMBLY
HQCD-XXX-XX.XX-XXX-XXX-X-X
04/29/03
SHEET
5
OF
8
BY:
KEVIN B
Training Edition
京公网安备 11010802033920号
EEWORLD
