5962-9471601H6C datasheet, PDF

Datasheet> All Categories > storage> storage> 5962-9471601H6C

5962-9471601H6C: DescriptionFlash Module, 128KX32, 150ns,; Categorystorage storage; File Size277KB，41 Pages; ManufacturerWhite Microelectronics

Download Datasheet Parametric View All

5962-9471601H6C Overview

Flash Module, 128KX32, 150ns,

5962-9471601H6C Parametric

Parameter Name	Attribute value
Maker	White Microelectronics
Reach Compliance Code	unknown
Maximum access time	150 ns
JESD-30 code	S-XHIP-P66
JESD-609 code	e4
length	27.305 mm
memory density	4194304 bit
Memory IC Type	FLASH MODULE
memory width	32
Number of functions	1
Number of terminals	66
word count	131072 words
character code	128000
Operating mode	ASYNCHRONOUS
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
organize	128KX32
Package body material	UNSPECIFIED
encapsulated code	HIP
Package shape	SQUARE
Package form	IN-LINE
Parallel/Serial	PARALLEL
Programming voltage	5 V
Certification status	Not Qualified
Maximum seat height	4.34 mm
Maximum supply voltage (Vsup)	5.5 V
Minimum supply voltage (Vsup)	4.5 V
Nominal supply voltage (Vsup)	5 V
surface mount	NO
technology	CMOS
Temperature level	MILITARY
Terminal surface	GOLD
Terminal form	PIN/PEG
Terminal pitch	2.54 mm
Terminal location	HEX
width	27.305 mm
Base Number Matches	1

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Added device type 05. Added case outlines M, N, 4, 5, 6, 7, and 8.

Added vendor cage code 88379.

Figure 1; For case outlines 5, 6, 7 and 8 changed dimension D3 min

and max from 1.030 and 1.040 inches to 1.020 and 1.060 inches.

Changed dimension A min from .156 inches to .135 inches. Changed

dimension L min from .145 inches to .132 inches. -sld

Added case outline 9. Figure 1; changed case outline M to be either

a single or dual cavity package. Figure 1; changed the dimension A2

max limit from .015 inches to .025 inches for case outline M. Added

thermal resistance ratings for all case outlines to paragraph 1.3 .

Added vendor cage 88379 for case outline M, device types 01

through 05. Table I; changed I

from 12.0 mA to 8.0 mA for the V

test. -sld

Added vendor cage code 0EU86 for device types 01 through 05, case

outline N. Drawing updated to reflect current requirements. -sld

Added case outline A. -sld

Added case outline B. Added note to paragraph 1.2.4. -sld

DATE (YR-MO-DA)

96-08-30

98-06-25

APPROVED

K. A. Cottongim

K.A. Cottongim

00-06-20

Raymond Monnin

03-01-13

03-02-21

03-11-10

Raymond Monnin

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

Steve L. Duncan

CHECKED BY

Michael C. Jones

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS

AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

AMSC N/A

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216

http://www.dscc.dla.mil

APPROVED BY

Kendall A. Cottongim

DRAWING APPROVAL DATE

94-12-16

MICROCIRCUIT, HYBRID, DIGITAL, FLASH

ERASABLE/PROGRAMMABLE READ ONLY

MEMORY, 128K x 32-BIT

SIZE

SHEET

CAGE CODE

REVISION LEVEL

67268

1 OF

5962-94716

DSCC FORM 2233

APR 97

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

5962-E013-04

1.4 Recommended operating conditions.

Supply voltage range (V

)........................................................

Input low voltage range (V

)......................................................

Input high voltage range (V

)....................................................

Case operating temperature range (T

) ....................................

A9 voltage for sector protect (V

) .............................................

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in

the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the

solitation.

SPECIFICATION

DEPARTMENT OF DEFENSE

MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.

STANDARDS

DEPARTMENT OF DEFENSE

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.

HANDBOOKS

DEPARTMENT OF DEFENSE

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Unless otherwise indicated, copies of the specification, standards, and handbook are available from the Standardization

Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in

accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as

designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class.

Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534).

Furthermore, the manufacturer may take exceptions or use alternate methods to the tests and inspections herein and not

perform them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device

class.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38534 and herein.

+4.5 V dc to +5.5 V dc

-0.5 V dc to +0.8 V dc

+2.0 V dc to V

+ 0.3 V dc

-55°C to +125°C

+11.5 V dc to +12.5 V dc

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

SIZE

REVISION LEVEL

5962-94716

SHEET

DSCC FORM 2234

APR 97

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.

3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4, 5, and 6 .

3.2.5 Block diagram. The block diagram shall be as specified on figure 7.

3.2.6 Output load circuit. The output load circuit shall be as specified on figure 8.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full specified operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are defined in table I.

3.5 Programming procedure. The programming procedure shall be as specified by the manufacturer and shall be available

upon request.

3.6 Marking of Device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked

with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.

3.7 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described

herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot

sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for

those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer

and be made available to the preparing activity (DSCC-VA) upon request.

3.8 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this

drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets

the performance requirements of MIL-PRF-38534 and herein.

3.9 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of

microcircuits delivered to this drawing.

3.10 Endurance. A reprogrammability test shall be completed as part of the vendor's reliability monitors. This

reprogrammability test shall be done for the initial characterization and after any design process changes which may affect the

reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the number of

program/erase cycles listed in section 1.3 herein over the full military temperature range. The vendor's procedure shall be kept

under document control and shall be made available upon request of the acquiring or preparing activity.

3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall

be done for initial characterization and after any design process change which may affect data retention. The methods and

procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein over the full military

temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of

the acquiring or preparing activity.

4. QUALITY ASSURANCE PROVISIONS

4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as

modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the

form, fit, or function as described herein.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

SIZE

REVISION LEVEL

5962-94716

SHEET

DSCC FORM 2234

APR 97

Recommended Resources

Simple AC power short circuit protection circuit

High voltage linear regulator HIP5600 circuit

Jinling brand KHJ2-10 ducted ventilation fan circuit diagram

Computer motherboard circuit diagram 815 1_29

Water dispenser circuit diagram 03

Gas water heater circuit diagram

Things to note when using peelable adhesive: The production process of PCB is complicated, with many high temperature and cutting procedures, such as welding, gold plating, leveling, etc., to make the substrate meet the expected requirements. Ho...; 造物工场PCB PCB Design

Last day! TI Live Broadcast with Prizes | Application of Precision ADC in Transmitters: Live Topic: Application of TI Precision ADC in Transmitters Live broadcast time: 10:00-11:00 am, August 19, 2022 (Friday) Introduction This live broadcast will introduce you to TI's precision ADC appl...; EEWORLD社区 Industrial Control Electronics

Renesas CPK-RA6M4 development board evaluation + SHT20 sensor reading data: RTT is very convenient to use. It encapsulates many packages, including a series of sensors. Today I will experience the portability of a sensor and quickly get started. The project is still based on ...; 流行科技 Renesas Electronics MCUs

Share 2018 Electronics Competition Paper - [B- Fire Extinguishing Aircraft] Fujian Province Ti Cup Special Prize / Xiamen University / Changmen University Team: [i=s]This post was last edited by Jacktang on 2021-8-5 10:39[/i]SummaryThe quadcopter is a small-sized, relatively simple-to-control aircraft. The quadcopter designed in this project uses only a TI MS...; Jacktang Electronics Design Contest

About the difference between CC1312R LAUNCHPAD versions: I bought a LAUNCHXL-CC1312R1 Rev: A development board online. The main chip is: XCC1312R1F3, and the development environment is: CCS920+simplelink_cc13x2_26x2_sdk_3_30_00_03. The current problem is: 1...; 火辣西米秀 Wireless Connectivity

About the signal input mode of the power amplifier: Regarding the selection of signal input mode of power amplifier. In professional audio engineering, we often encounter problems such as signal parallel connection and bridging. First of all, we must c...; fish001 Analogue and Mixed Signal

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components