DEVICE PARAMETERS, FIXED and ADJUSTABLE REGULATORS
f
O
Oscillator Frequency
50
52
100/
500
nA
kHz
kHz(min)
kHz(max)
V
V(max)
%
%(max)
A
A(min)
A(max)
mA(max)
mA
mA(max)
mA
mA(max)
µA
µA(max)
°C/W
47/
42
58/
63
Saturation Voltage
Max Duty Cycle (ON)
Current Limit
I
OUT
= 1A (
Note 4
)
(
Note 5
)
Peak Current, t
ON
≤
3µs (
Note 4
)
0.9
1.2/
1.4
98
93
2.2
1.7/
1.3
3.0/
3.2
2
75
30
5
10
Standby Quiescent Current
ON/OFF Pin = 5V (OFF)
50
200
65
45
2
85
100
1.4
1.2
4
30
ON /OFF Pin = 0V (ON)
0.01
10
2.2/
2.4
1.0/
0.8
V
SAT
DC
I
CL
I
L
Output Leakage Current
V
IN
= 40V, (
Note 6
),
(
Note 6
)
(
Note 6
)
Output = 0V
Output = –1V
Output = –1V
I
Q
I
STBY
Quiescent Current
T Package, Junction to Ambient (
Note 7
)
θ
JA
Thermal Resistance
T Package, Junction to Ambient (
Note 8
)
θ
JA
θ
JC
T Package, Junction to Case
N Package, Junction to Ambient (
Note 9
)
θ
JA
WM Package, Junction to Ambient (
Note 9
)
θ
JA
ON/OFF CONTROL, FIXED and ADJUSTABLE REGULATORS
Test Circuit Figure 1
V
IH
V
IL
I
IH
I
IL
Notes:
ON/OFF Pin Logic
Input Level
ON/OFF Pin Logic
Current
V
OUT
= 0V
V
OUT
= 5V
ON /OFF Pin = 5V (OFF)
V(min)
V(max)
µA
µA(max)
µA
µA(max)
1. Absolute Maximum Rating indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical
Characteristics.
2. All limits guaranteed at room temperature (standard type face) and at
temperature extremes (bold type face).
All room temperature limits are100%
production tested. All limits at
temperature extreme
are guaranteed via testing.
3. External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the
LM2575/LM1575 is used as shown in Figure 1 test circuit, system performance will be shown in system parameters section of Electrical
Characteristics.
4. Output (pin 2) sourcing current. No diode, inductor or capacitor connected to output.
5. Feedback (pin 4) removed from output and connected to 0V.
6. Feedback (pin 4) removed from output and connected to 12V to force the output transistor OFF.
7. Junction to ambient thermal resistance (no external heat sink) for the 5-pin TO-220 package mounted vertically, with 1/2" leads in a socket, or on PC
board with minimum copper area.
8. Junction to ambient thermal resistance (no external heat sink) for the 5-pin TO-220 package mounted vertically, with 1/4" leads soldered to PC
board containing approximately 4 square inches of copper area surrounding the leads.
9. Junction to ambient thermal resistance with approximately 1 square inch of pc board copper surrounding the leads. Additional copper will lower
[font=微软雅黑][color=#333333][font=微软雅黑][color=#444444]Recently, I have sorted out and collected some information about engineers using SD NAND on MCUs (mainly some mainstream STM32, Allwinner V3S and ot...
When downloading a program to the flash of the SM320F2812 chip, I found that the buttons on the On-Chip Flash Programmer interface are all gray, and only the Unlock button is lit and can be used. Howe...
I started playing board games 6 years after graduation.
It's been almost 9 years, and I don't have many boards.
Many lost their belongings when they graduated, worked or moved.
The rest are reluctant ...
My colleague asked me to test the voltage difference between the diode anode marked by the red circle and the busbar and 12Vo-. The waveform is as follows. Is this called clamping voltage? Switching n...
[i=s]This post was last edited by bigbat on 2021-12-18 12:17[/i]When I was explaining resistors, capacitors, and inductors to some non-professional colleagues, the inductor gave me the most headache. ...
Indoor 5G antenna solution2.1 Typical digital indoor distribution system
Typical indoor distribution scenarios include government and enterprise office buildings, shopping malls, hotels, hospitals, et...
MCU
京公网安备 11010802033920号
EEWORLD
