PFC-W2010LF-02-1001 datasheet, PDF

Datasheet> All Categories > PFC-W2010LF-02-1001

Preview

PFC-W2010LF-02-1001: DescriptionPrecision Thin Film Chip Resistors; File Size387KB，4 Pages; ManufacturerIRC ( TT Electronics ); Websitehttp://www.irctt.com/

Download Datasheet View All

PFC-W2010LF-02-1001 Overview

Precision Thin Film Chip Resistors

Preview

Download Datasheet

View All

Precision Thin Film

Chip Resistors

PFC Series

•

Standard 60/40 Sn/Pb and Pb-free (RoHS compliant) terminations available

•

Available in 0402, 0603, 0805, 1206, 1505, 2010 and 2512 chip sizes

•

Tested for COTS applications

•

Absolute TCR to ±10ppm/°C

•

MIL screening available

IRC Advanced Film Division

Ultra stable Tantalum Nitride

resistor ﬁlm system

Non-leaching

Nickel barrier

Wrap around

termination

The IRC TaNFilm

PFC chip resistor series provides the high precision and ultra stable performance of our

Tantalum Nitride resistive ﬁlm system in 0402, 0603, 0805, 1206, 1505, 2010 and 2512 sizes. The unique

characteristics of the passivated Tantalum Nitride ﬁlm insure long term life stability and stability in most envi-

ronments.

Using the same manufacturing line as the PFC Military Series, IRC’s precision chips maintain the same supe-

rior environmental performance. Specially selected materials and processes insure initial precision is main-

tained in the harshest surface mount soldering environment. Wrap-around terminations with leach-resistant

nickel barriers insure high integrity solder connections.

Electrical Data

Model

Power Rating

(70°C)

50mW

100mW

250mW

333mW

350mW

800mW

1.0W

Max Voltage

Rating (≤

√

P x R)

75V

100V

200V

100V

175V

200V

-55°C to +150°C

2KV to 4KV

(HBM)

<-25dB

Temperature

Range

ESD

Sensitivity

Noise

Termination

Substrate

W0402

W0603

W0805

W1206

W1505

W2010

W2512

60/40 Sn/Pb

or 100% tin

(RoHS

compliant)

plated over

nickel barrier

99.5%

Alumina

General Note

IRC reserves the right to make changes in product specification without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

• Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com

A subsidiary of

TT electronics plc

PFC Series Issue May 2008 Sheet 1 of 4

Recommended Resources

Radio circuit of monolithic integrated circuit radio

Tube amplifier rectifier circuit diagram

voltage follower circuit

Enlarged indication schematic diagram (with thermocouple) circuit

100kHz crystal-unijunction transistor relaxation oscillator

Thermocouple AD conversion circuit

MSP430F15X/16X series DMA registers: DMA interrupt: During data transmission, when the DMAxSZ register value decreases to 0, DMA sets DMAIFG. The DMA interrupt and DAC12 module share the interrupt vector. When using the interrupt, the so...; 灞波儿奔 Microcontroller MCU

[RVB2601 development board trial experience] Build a development environment and test the serial port routine: According to the tutorial, build the development environment and serial port routine test.1. Download the software1.1 Development board resources Download address: RVB26011.2. USB to TTL driverUSB to ...; TL-LED XuanTie RISC-V Activity Zone

Is there a better analog switch than CD4051?: I want to use CD4051 to switch 10V voltage. My control is 5V, but CD4051 needs 7V for high level when VDD=10V, so I use CD4504B to convert the level. I don't know if there is a better chip than CD4051...; bigbat MCU

Lichee RV 86 PANEL Review (3) - Building a cross-compilation chain under WSL single system: # Lichee RV 86 PANEL Review (3) - Building a cross-compilation chain under WSL single system## Why download cross-compilation tools? The compilation tool chain on the PC is gcc, ld, objcopy, objdump, ...; jszszzy Special Edition for Assessment Centres

DSP bootloarder C5000: When I first started learning DSP, the most troublesome thing was the DSP bootload problem. When I was learning 51 before, as long as the program was written and compiled, I could use the burner to bu...; 灞波儿奔 DSP and ARM Processors

What is the minimum distance that the inductor of a switching power supply chip should be kept from the edge of the board?: When making a board for medical equipment, TPS5430 (switching frequency 500KHz) was used as a step-down chip. During the layout, this part of the circuit was located on the edge of the board. I am wor...; mmmllb Power technology

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components